A combustion chamber is used to burn a fuel mixture consisting of methane and ethane. The fuel enters the chamber at a temperature of 25°C and a pressure of 1 atm. Dry air enters the chamber at a temperature of 200°C and a pressure of 1 atm. Excess air is used for combustion. Assume the air to be 21.0 mole% O2 and the balance N2. The flue gas exits at a temperature of 800°C and a pressure of 1 atm. Analysis of the flue gas has the following composition in mole percent: 1.62% CO, 8.52% CO2, 4.21% 02 and the balance N2. Calculate the % of methane in the fuel

Q: Use water as a drilling mud to drill a well to a depth of 3000 feet , calculate the pressure…

A: This question is based on pressure gradient. The data given are: Depth = 3000 feet

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: A process flow diagram of an anode fuel cell.

A: The process of creating a process flow diagram (PFD) for an anode fuel cell entails putting the…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: Explain steady flow in relation to fluid mechanics.

A:

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: Following is the example of. O a. Orifice meter O b. Flow O C. Flow Pressure meter Rotameter

A: In the given image, the device contains a transparent glass tube that is placed vertically.  In this…

Q: crystallization mechanism,

A: Crystallization is a process in which mass transfer of solute takes place from the liquid solution…

Q: Given a 35% mixture, what will be the time of flow? * O 43.5% O 41.5% O 6.6% 6.5%

A:

Q: Illustrate and discuss the process flow for the manufacture of porcelain

A: Solution-Step:  (a) Component needed(i) Feldspars K2O.Al2O3.6SiO2 & Na2O.Al2O3.6SiO2(ii) Quartz…

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: What is a  vane-axial cyclone seperator?

A: This question is from cyclone separators which form an important part in separation processes. The…

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Give the relation between overall and individual height of a transfer units.

A: In the design of packed towers, the total height of towers is given as, ZTU = NTU×HTU Here, ZTU is…

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: Explain the concept of fluid flow and its significance in chemical engineering processes.

A: The study of fluids, which includes liquids and gases, is known as fluid flow. Fluids may flow and…

Q: Gas processing plant process flow diagram and explanation

A: A gas processing plant is an industrial facility that purifies raw natural gas extracted from wells…

Q: If I want do a certain application in the process engineering, what is the best type of pump that…

A: Classification of pump:

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: Using data from part 1, plot a log-log graph of pressure drop (Ap) vs air flow, with a separate…

A: In any fluid-carrying system, the Pressure drop ∆P is the difference in total pressure between two…

Q: If the time of flow of the given mixture is 50 seconds, what is the composition of the mixture? * O…

A:

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: production of paper from ground nutshell complete flow chart

A: In this question flow chart of production paper from ground nutshell is to be discussed.

Q: When we change the fluid package from one package to another, does the temperature and pressure…

A: When we change the fluid package from one another then the following properties will change such…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: When using an aspirator as a source of vacuum in a vacuum distillation, do you turn off the…

A: It is to be mentioned if the aspirator is turned off before venting the system or not.

Q: What does a HYSYS fluids package represent thermodynamically

A: In chemical engineering, there are many calculations that can be done manually. But some are very…

Q: Explain and describe possible factors that may affect fluidization.

A: Fluidization parameter (calculated via inlet air drift fee and rotor speed), stress distinction over…

Q: Discuss Lever-Operated Knapsack Sprayer

A:

Q: Distinguish between Newtonians and Non-Newtonians fluids with graphs and examples

A: Newtons Law of viscosity states that the shear stress between the layers of the fluid is…

Q: What are centrifugal pumps?

A: Pump: Pump is a mechanical device which is widely used in chemical industry to transport of fluid…

Q: Given a 60% mixture, what will be the time of flow? * О 90% O 80% O 48% О 45%

A:

Q: Describe with neat diagrams various types of commercial evaporators. Discuss the important features…

A: Evaporators  Evaporators heat exchange systems used for concentration , dewatering and…

Q: With the help of a neat drawing of a condenser, discuss its design procedure with the important…

A: condenser and its design

Q: Equally spaced trays are placed and provided with downspout and weirs inside the tray tower is to a.…

A: Answer:  Increase the contact between gas and liquid inside the column.

Q: Represents and describes by means of a diagram the main parts of the evaporation equipment.

A: Evaporation  It is the process of concentrating the stream by removing water. The process is energy…

Q: What are the advantages and disadvantages of continuous, counterflow, mechanically assisted…

A: The advantages of the mechanically assisted forms of the continuous and counter-flow extractors are…

Q: What is the method or heory that the laborator device depends on in measuring potassium?

A:

Q: Explain in detail the temperature and humidity gradients in cooling tower.

A: Detailed description of cooling tower temperature and humidity gradient needed to be described.

Q: Discuss in detail (Diagram, Working and Application) about any one Flow measuring devices

A: The flow measuring device is the device that is inserted into the flowing fluid that produces a…

Q: increasing of the column pressure, results in

A: Column pressure is the pressure of liquid due to its height. Pressure has direct effect on the…

Q: Why is centrifugal force frequently applied to speed up and facilitate particle-fluid separation?

A: Centrifugation technique uses centrifugal force for the separation of very fine particles from the…