Chapter 4: Practice problemsf 1 kN, 2 kN and 3 kN at 1, 2 and 4 m1. A cantilever beam of length 4 m carries point loadsfrom the fixed end. Construct the shear force and bending moment diagrams for the cantilever.1mA1 kN2m84m1m4 kNC+2. A simply supported beam of length 8 m carries point loads of 4 kN and 6 kN at a distance of2 m and 4 m from the left end. Construct the shear force and bending moment diagram for thebeam.2m2 kN8 mC+6 kN2mD3 kND4. Draw the shear force and bending moment diagram for a simply supported beam of length 9m and carrying a uniformly distributed load of 10 kN/m for a distance of 6 m from the left end.Also calculate the maximum B.M. on the section.3. A cantilever of length 2.0 m carries a uniformly distributed load of 2 kN/m length over thewhole length and a point load of 3 kN at the free end. Draw the S.F. and B.M. diagrams for thecantilever beam.References:[1] A text book of Mechanics of materials by Dr.R.K.Bansal, Laxmi publishers, PublishedDecember 30th 2005.[2] A text book of Strength of materials by R.S.Khurmi,S.Chand Publishers, 2008.[3] Mechanics of Solids, Bhavikatti, S.S. New Age International Ltd 2000,ISBN: ISBNnumber: 9788122427660, ISBN number: 9788122428582(ProQuest)

“Since you have posted a multiple question, we will provide the solution only to the first question…

Chapter 4: Practice problems 1. A cantilever beam of length 4 m carries point loads of 1 kN, 2 kN and 3 kN at 1, 2 and 4 m from the fixed end. Construct the shear force and bending moment diagrams for the cantilever. 1m 1 kN 8 + 1m 2 kN + 2m 3 kN D

Chapter 4: Practice problems 1. A cantilever beam of length 4 m carries point loads of 1 kN, 2 kN and 3 kN at 1, 2 and 4 m from the fixed end. Construct the shear force and bending moment diagrams for the cantilever. 1m 1 kN 8 + 1m 2 kN + 2m 3 kN D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Draw the free body diagram, shear force diagram, and bending moment diagram for the beam shown below and calculate values at each point:
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
Draw the shear and bending moment diagrams for the cantilevered beam below (figure not to scale). Identify the location and magnitude of max shear and bending stresses. 20 in 10 in 10 in 70 in 80 lbs 20 lbs 32.5 lbs
SHEAR AND MOMENT DIAGRAM PROBLEM 2 Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 6.9 ft, b = 10.4 ft, c = 5.8 ft, and w = 9.5 kips/ft. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. The roller at point D indicates that motion is restricted both up and down, and the beam will not lift off the roller. a B W b C D X
In Problems 8-51 to 8-68, beams are loaded and supported as shown in the accompanying figures. Draw complete shear and moment diagrams for 5000 lb 8000 Ib B. -4 ft 5 ft 4.5 ft
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b=3.0 ft, c= 7.0 ft, w = 9 kips/ft and M = 300 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. " " Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i W i a W M a B M B ес b kips kips с Cy с X с -X
For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Calculate the shear force V and bending moment M at a cross section located 0.5 m from the fixed support. Neglect the weight of the beam. (Show complete calculation and step by step process. Show free body diagram)
PART 1 1. Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=11 ft, b=5 ft and w = 11.5 kips/ft. IMAGE* 2. Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* Answers: Ay = ? kips, Cy = ? kips PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 11 ft(c) x = 14.333333333333 ftWhen entering your answers, use the shear force sign convention.Answer:(a) V = ? kips.(b) V = ? kips.(c) V = ? kips. PART 3 The shear-force diagram crosses the V = 0 axis between points A and B. Determine the location x where V = 0 kips.Answer: x = Enter your answer in accordance to the question statement ft. PART 4 Determine the maximum bending moment that acts anywhere…
For the problem shown below (left), W = 51 lbs while L1 = 4.4 inches and L2 = 12 inches. This results in the shear force diagram as shown on the right, where A, is the reaction force in the vertical direction at point A. Based on this shear diagram, what is the maximum moment in the portion of the horizontal beam from x = O to x = L1 in units of lb-in to two decimal places. (Be sure to use a negative sign to designate a negative moment if necessary.) A |--L1-——————— L2 Ay lb 0 -Ay lb W L1 L2 W -L1- BO L1- -X
For the structural frame shown in figure (4), draw the axial, shear forces and bending moment diagrams for member abc. 20 kN/m 3m b 3m a ZRoller Pin 4m 4m Figure (4)