Centroid Show complete and step by step solution and detailed illustrations. Limit your answer into 3 decimal places

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility = c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: Using the image on the Moment of Inertia Tab, where the following criteria are considered: Assign…

A: The moment of inertia tab is given. The torque applied is given as, T=2 N-m

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: 4.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: acting along line b-b.We can resolve the force F into its x and y components using the following…

Q: resolve solution

A:

Q: Learning Goal: To apply the condition of equilibrium to three- dimensional systems and solve for…

A:

Q: A 100 mm by 150 mm rectangular plate QABC is deformed into the shape shown by the dashed lines in…

A: Given Data: H=100 mmB=150 mm   To Find: (a) Strain components εx, εy, γxy. (b) Principal strains…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A: Given Data, W = Weight of the seesaw = 45 lb L = Length of the seesaw = 5 m Condition 1 :-…

Q: Draw a perspective,isometric(with 30 angle), & oblique(with 45 amgle) view of a cube.

A: Draw a perspective,isometric(with 30° angle), & oblique(with 45° angle) view of a cube.

Q: Draw an isometric sketch of the object from the viewpoint W-Corner.

A: According to the details provided in the question, we need to calculate the isometric view.

Q: 5-9. The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of T the largest…

A: Given: The diameter of the shaft, d = 50 mm The allowable shear stress = 60 MPa

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the…

A: To draw: Free body diagram of the boom. Given: The connection at A is pin. Sketch: The force In wire…

Q: find the centride of area of ​​X and Y.

A:

Q: Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and…

A: To find Determine the minimum diameter, d for the rod that will achieve a minimum static factor of…

Q: 2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: ## Determining the Net Torque on the Wheel (Considering the Image)The image  shows a wheel with…

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: Determine the magnitude and coordinate direction angles of the resultant force acting at point A on…

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: Find a "flat" object in your house, make necessary measurements, and then calculate the center of…

A:

Q: Use a trammel to sketch the missing symmetric half of the figure. Do not dimension.

A: Given Sketch To find The symmetric half of sketch

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. An Effort…

A: Write the value of load.   R=90 N   Write the value of effort.   E=30 N

Q: a) Determine the Area and the centroid of the shape. Show the calculations using integration. b)…

A:

Q: Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm.…

A:

Q: Find: centroidal centroidal lx = ly= Ix, = ly =

A:

Q: Please give answer clearly with each steps.

A:

Q: Compute the coordinates of the centroid (x, y) of the area shown.

A:

Q: 2. For the shaded area shown, determine a. The location of its centroid b. The moment of inertia and…

A: Given C shaped structure To find Centroid location Moment of inertia for X and Y axis Radius of…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.