Centrifugal pump impeller runs at 950 rpm. Its external and internal diameters are500 mm and 250 mm. The vanes are set back at an angle of 35° to the outer rim. Ifthe radial velocity of water through the impeller be maintained constant as 2 m/sec,find the angle of the vanes at inlet, the velocity and direction of water at outlet andthe work done by the impeller per kg of water

Given: The speed of impeller, N = 950 rpm The external diameter of impeller, D = 500 mm The internal…

Answered: Centrifugal pump impeller runs at 950…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the followwing problem: Determine the number of stages needed for a centrifugal pump if it is used to deliver 600gal/min of water and pump power of 15Hp. Each impeller develops head of 38ft. Calculate the compressor work in kJ required to compress 1 kg of an ideal gas from an initial volume and pressure of 0.65m3 and 101.3kpa to a final pressure of 517kpa & volume of 0.1943m3.ANS. 133.549 An air compressor takes air at 97kpa at the rate of 0.4m3/s and discharges to 650kpa. If power input to the compressor is 110kw, determine the heat loss(kw) in the compressor. ANS. 11.948
The inlet and outlet diameters of a centrifugal impeller are 0.2m and 0.4m resp.the van angle at outlet 45 degree the pump speed is 1000 rpm.the normal velocity of radial flow through the impeller is constant at 3m/s.the entry of the water is at radial direction determine the van angle at inlet the absolute velocity at outlet and the net head produced by the pump 12:04 PM /
4. A centrifugal pump delivers 1500 L/min of water from an initial pressure of 156 kPa to a final pressure of 328 kPa. The area of the inlet pipe is 315 cm² and the area of the discharge pipe is 80 cm?. Solve for the power input to the pump, kW.
A reaction turbine has mean blade speed of 220 m/s and blade speed to steam velocity ratio of 0.7. Determine the angle at inlet of blade and work done per kg of steam flow if angle at exit is 20°.
A water jet with a flow rate of 2.83 m3 / s is traveling at 6 m / s in the positive x direction. The cost of the current striking a stationary splitter is correct about a 45 aç angle, other company are deflected downwards by the same angle and the final velocities of the two streams are 6 m / s. By neglecting the gravity, the separator is in place against the force applied by the water. calculate the x- and z- power of what is required to hold it. For water ? = 1.184 kg / m3
A twin-engine jet aircraft is climbing at a 10 degree angle, measured from the vertical, at 260 ft/s. The thrust developed by an engine is 1000 lb. Calculate the power developed by the whole aircraft.
29Water enters the impeller of a centrifugal pump radially at a flow rate of 250 L/min. The rotational speed of the impeller shaft is given as 400 rpm. Since the outer diameter of the impeller is 60 cm and the tangential component of the output velocity at this point is 55 m/s, calculate the torque (Nm) coming to the impeller.
An open reservoir on ground level is used to store water to be pumped up to an overhead tank (also open) 200 ft ave ground. Calculate the work done by the pump (in J/kg) to give an exit velocity of 40 m/s. Ignore friction and use alpha = 1.00. Evaluate the pressure term Evaluate he kinetic energy term Evaluate the potential energy term Hence calculate the work done by the pump What minimum power of pump (in KW) would be needed to provide a mass flowrate of 0.27 kg/s Training
The performance characteristics of a certain centrifugal pump are determined from anexperimental setup shown in the figure. When the flow rate of a liquid (SG= 0.9) through thepump is 120 gpm, the pressure gage at (1) indicates a vacuum of 95 mm of mercury and thepressure gage at (2) indicates a pressure of 80 kPa. The diameter of the pipe at the inlet is110 mm and at the exit it is 55 mm.If Z2-Z1= 0.5 m, what is the actualhead rise across the pump? Explainhow you would estimate the pumpmotor power requirement.
Air flows through a turbojet engine at the rate of 50.0 kg/s and the fuel flow rate is 1.0 kg/s. The exhaust gases leave the jet nozzle with a relative velocity of 600 m/s. Compute the velocity of the airplane, if the thrust power is 1.5 MW in the following two cases: 1. Pressure equilibrium exists ver the exit plane 2. If the pressure thrust is 8 kN
The opening at point C is inclined at 45 degrees. Find the maximum height that the water can reach, measured from the datum line. Also, calculate the range.
Wind at standard atmospheric pressure and 15°C temperature has a velocity of 20 m/s. The turbine has a diameter of 60 m and its operating speed is 50 rpm at maximum power coefficient (take CP=0.593). Calculate: a. The total power density in the wind stream (kW/m2) b. The maximum power density assuming overall efficiency = 40% c. The total power produced in kW assuming overall efficiency = 40%

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS