Censistentdefor. Ex5n Analyze the frame shown. method Cassume re dundants are using Cx cund Cy) GL Constard To kN/m The Freme is Indet. 50kN. -> to 4he 2nd degree -8-X 5m to

Q: Determine the true length of lines SD and PF. Then draw the point view of line SD. Use only two…

A:

Q: I. True or False. Write TRUE if the statement is correct and FALSE if the statement is incorrect. 1.…

A: Given statements:1. Stress is pressure exerted on a material object; it may have a unit of kN.2.…

Q: 5.1.20 The truss shown in the figure con- sists of-4 bays of 'K' structure. Each bay has 2 m long…

A:

Q: Civen that the tension in segment AB 130 N WITH a rathio of 1H: 2v, which of the fo llowing nearly…

A:

Q: Draw the FDBS of member ADB and BEC 1 m 1m B |C E 1 m 1.6 m A

A:

Q: Problem 23.4. A hook carries a load of 7.5 kNand the load line is at a distance of 20 mm from the…

A: Here we will use the concept of bending of curved bars to calculate the value of stresses. Given…

Q: 150kv Shinge R=4m A रजेट Compuk the value af P such that zero, then the moment at A 's draw N-F.D,…

A: Force equilibrium in Horizontal and vertical direction Fx=0HA-P=0  ⇒  HA=P…

Q: the design moment capacity of the beam

A:

Q: The uniferm arcer ectangular thin plate has dimensicrs indicated and masS M- 52 kg. 2. T 4.5m…

A:

Q: lre the method of Uirtuat work to determine the vertical duplacement Of Joints B and D af the Jteel…

A: Using the unit load method: Deflection DB/D=mML/AE Where, m=Force in member due to the unit load M=…

Q: ● Analyze the simple truss shown.

A: Given:- To find:- Analysis of the truss

Q: Calculate Newtons Oistance and fora metres. in in Table %o Ercor Left Reachon R Right Reochon RK…

A: Consider the given figure. Show the load in Newton.

Q: How many blocks are necessary to build a 261 (S.F.) wall area with the following conditions? Note Do…

A:

Q: The bloch has a velicaty 4= armls at A ard a Velsaity Ug- 15 m/s as it parses point B on the…

A:

Q: 5. 25 mm x- (horizontal) and y- (vertical) axis through the centroid of the two 250 x 25 mm steel…

A: Given Steel plate at top and bottom Channel section at right and left  Welded together to form cross…

Q: Determine the vertical displacement of joint Cof the truss. Each member has a cross-sectional area…

A: Due to symmetry, the vertical reaction at point A and E can be given as, Ay+Ey=4+3+3 kN=10  kN So,…

Q: Virtual Work for Beams and Frames #2 Determine the slope and the displacement at the end C of the…

A: By assuming the value of P is 8 and value of a is 3

Q: use Trapezcidal rule to approxunate 24 1-e dx 1-2 x+2x -1

A: Given to approximate: I=(1-e2)∫1.22.11x2+2x-1 We have here, f(x)=1x2+2x-1, such that…

Q: 10 GN/m² to kip/inch²

A: Given unit is GN/m2 1GN=224808.94kip And 1m=39.37inch

Q: Draw the B.M.D for the following

A: The diagram given in the question is as follows:

Q: Determine the force-couple system acting at point 0. 50 N 90 N 40° В 40 N m 400 mm 1300 mm A 4 800…

A:

Q: Compute the tensile strength of an angle section ISA 150 x 115 x8mm of Fe 410 grade of steel…

A:

Q: Design the beam shown 30kN W = 8m -1m

A: The given values are as follows,f'c=28MPadb=25mmϕGr60d12mmϕAssume b=d2The design  of the beam is…

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS 3.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND…

A:

Q: A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS B.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND…

A: GIVEN BEAM IS A OVERHANG BEAM WHICH IS OVERHANG ON BOTH THE SIDES  TOTAL LENGTH OF SPAN=17m…

Q: Selve the fiven beam by sechan method to calculete reaction for ces and clat DIaw shear foce and…

A: Let RA and RB be the reactions at supportRA+RB=40+5×16'RA+RB=120  Now, taking moment at A, which is…

Q: A davit supports a load P= 48 kN, as shown in the figure. For cross section A-A, (a) calculate the…

A: Davit support is given, which supports a load P = 48kN The cross-section of the support at section…

Q: Exse Analyze the frame shown using consistent defor. method Cassume redundants are CX and Cy In…

A: Method of Consistent Deformations (Flexibility Method): Consider the free body diagram of the given…

Q: Solve fast please I need correct answes

A:

Q: - A bronze bar 3m long, mith a cnes- sectiomal area y 3oomm? is Mlaced between two ngid walls. At a…

A:

Q: PLATE # 3 CALCULATE O. AND Yo Of THE BEAM LOADED AS SHOWN USIN G CONJU GATE BEAM METHOD 5KNlm 20KN…

A: To determine: Deflection and Slope at point C

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.