Caster oil at 36°C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surface temperature of 96°C, determine (i) The thermal boundary layer thickness at the end of the plate (ii) The local heat transfer coefficient at the end of the plate.

Caster oil at 36°C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surface temperature of 96°C, determine (i) The thermal boundary layer thickness at the end of the plate (ii) The local heat transfer coefficient at the end of the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider steady, laminar, two-dimensional flow over a hot plate. Does the convective heat transfer coefficient (h) increase, decrease, or remain constant with distance from the leading edge? Explain.
Question 1 15 points Save Answ Engine oil at 87°C flows over the upper surface of a 5-m-long flat plate whose temperature is 18°C with a velocity of 5 m/s. Determine the total drag force and the rate of heat transfer per unit width of the entire plate (Insert answer for Fp, h and Q) W/m2K kW
Engine oil at 100°C and a velocity of 0.15 m/s flows over both surfaces of a 1.2-m-long flat plate maintained at 20°C. Determine: (a) The velocity and thermal boundary layer thicknesses at the trailing edge. (b) The local heat flux and surface shear stress at the trailing edge. (c) The total drag force and heat transfer per unit width of the plate. Determine the velocity boundary layer thickness & at the trailing edge, in m. 8 = i m Determine the thermal boundary layer thicknesses 8, at the trailing edge, in m. m Determine the magnitude of the local heat flux at the trailing edge, W/m?. q" x W/m2 i Determine the local surface shear stress at the trailing edge, in N/m?. Ts, L. = N/m2 Determine the total drag force per unit width of the plate, in N/m. D' = i N/m Determine the magnitude of the heat transfer per unit width of the plate, in W/m. W/m
question is image only part a
1. The upper surface of a 50-cm-thick solid brass plate (k=109 W/m·K) is being cooled by water with temperature of 10°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 190°C, respectively. Determine the water convection heat transfer coefficient and the water temperature gradient at the upper plate surface. Water 1111 Ts,2
A 21.5-cm-wide and 31 cm high vertical hot surface in 20°C air is to be cooled by a heat sink with equally spaced fins of rectangular profile. The fins are 0.1 cm thick, 4 cm wide, and 31-cm- long in the vertical direction. Given: Consider the characteristic length to be the height of the surface. The properties of air at T₁ = 52.5°C: k = 0.02753 W/m °C, v= 1.823 × 10–5 m²/s, Pr = 0.7222 a. Determine the optimum fin spacing of the heat sink if the base temperature is 85°C. b. Determine the rate of heat transfer by natural convection from the heat sink if the base temperature is 85°C.
Determine the thermal boundary thickness(mm) of flow over a flat plate which has a 0.5 mm boundary layer thickness. Take u= 25 x 10 Pas, C,=2.0 kJ/kg K and k=0.05 W/m K.
Air is flowing at 35°F with a velocity of 12 ft/s over a plate 10 ft long and 2 ft wide. The plate is at room temperature. Determine the coefficients of local friction, heat transfer coefficient and heat transfer rate of the plate at 1 ft intervals along the length. Plot on the same graph the results as a function of distance from the leading edge, the graph will be reviewed. The table of thermal properties of air is on the platform. Report in the following boxes your results for a length of 5 ft.
Engine oil at 100°C and a velocity of 0.20 m/s flows over both surfaces of a 1.1-m-long flat plate maintained at 20°C. Determine: (a) The velocity and thermal boundary layer thicknesses at the trailing edge. (b) The local heat flux and surface shear stress at the trailing edge. (c) The total drag force and heat transfer per unit width of the plate. Determine the velocity boundary layer thickness & at the trailing edge, in m. 8 = i m Determine the thermal boundary layer thicknesses &, at the trailing edge, in m. 8, = i m Determine the magnitude of the local heat flux at the trailing edge, W/m². q" x = i W/m² Determine the local surface shear stress at the trailing edge, in N/m². Ts, L i N/m² Determine the total drag force per unit width of the plate, in N/m. D' = i N/m Determine the magnitude of the heat transfer per unit width of the plate, in W/m. d' = W/m i
Heat transfer
In the arctic sea, the ice sheets are melting. Let's calculate the temperautre distribution in one such ice sheet. The sheet is 2 m thick. Under the sheet there is ice-water mixture and it can be assumed that the temperature of the bottom surface of the ice sheet is approximately 0°C. Air at -20°C is blowing above the sheet. The convection coefficient of air is 15 W/m².K. The thermal conductivity of ice is 2.2 W/m.K. What is the temperautre of icesheet at its center (i.e., at 1 m from the surface)?
Thick fluids such as asphalt and waxes and the pipes in which they flow are often heated in order to reduce the viscosity of the fluids and thus to reduce the pumping costs. Consider the flow of such a fluid through a 100-m-long pipe of outer diameter 30 cm in calm ambient air at 0oC. The pipe is heated electrically, and a thermostat keeps the outer surface temperature of the pipe constant at 250C. The emissivity of the outer surface of the pipe is 0.8, and the effective sky temperature is-300C. Determine the power rating of the electric resistance heater, in kW, that needs to be used. Also, determine the cost of electricity associated with heating the pipe during a 10-h period under the above conditions if the price of electricity is $0.09/kWh. Properties The properties of air at 1 atm and the film temperature of (Ts+To)/2 = (25+0)/2 = 12.5°C are: k = 0.02458 W/m.oC, v = 1.448x10-5 m2/s, Pr = 0.7330 D=m