Carbon dioxide gas flows from a large tank (at temperature 50 °C and pressure 2 atmosphere under adiabatic conditions into a second tank through a horizontal converging nozzle) diameter of throat equal t7 cm) Z 40 The pressure at the second tank and at the nozzle throat is(1.3atmosphere. - Calculate the mass flow rate of carbon dioxide gas assuming frictionless flow. - Calculate Mach number in the nozzle throat. Molecular weight of Carbon dioxide = 44 C₂/C, (y) for Carbon dioxide = 1.3 Vie IRT Must

Q: Q5-B) A wooden cylinder (y=5.8 kn/m³) floats in an oil (S.G-0.9). How much of the cylinder extends…

A:

Q: Air at atmospheric pressure flows across a staggered tube bank consisting of 8 rows of tubes in the…

A:

Q: From the figure below, both the tank and the slanted tube are open to the atmosphere. If L = 3.12 m,…

A: This system follows hydrostatic law and this law is to calculate the pressure at any point at rest…

Q: Mass flow rate of the water along the length of the hose: [Select] Velocity of the water along the…

A:

Q: A 4 inch Sched 40 steel pipe carries crude oil at 80°C. The crude oil has a dynamic viscosity of 1.2…

A: Given: 4 inch Schedule 40 steel pipe dynamic viscosity μ =1.2 x 10-2 Pa·s density ρ= 680 kg/m3

Q: Q:-Determine the force exerted on the cone curved surface. The liquid in the tank has a specific…

A: Given Absolute pressure of air in tank=151 kPa Specific weight of liquid=27 kNm3 So exerted pressure…

Q: air h, h, water

A: Given Density of water ρw =1000 kg/m3 h1 = 60 cm h = 45 cm h2 = 180 cm Find-Difference of…

Q: 17-86 Air enters a normal shock at 22.6 kPa, 217 K, and 680 m/s. Calculate the stagnation pressure…

A: Assume that ;Air is an ideal gas with constant specific heats and Flow through the nozzle is steady,…

Q: Air enters a nozzle steadily at 2.21 kg/m and 30 m/s and leaves at 0.762 kg/m' and 180 m/s. If the…

A: Given   Density at inlet  of air(ρ 1) = 2.21 kg/m3 Velocity at inlet of nozzle (V1) = 30 m/s Inlet…

Q: Air passes through a horizontal duct with steady state conditions. The air enters with parameters…

A:

Q: sider a U-tube whose arms are open to the atmo one arm and light oil (poil = 790 kg/m³) from the…

A:

Q: 17. Calculate the pressure at point A in Fig. 2.50. The slope of the tube is 4 horizontal to 1…

A: Reservoir review is given.Calculate pressure at point A.

Q: Consider the sealed containers (same fiuid and on the same ground level) below with heights given in…

A:

Q: The initial free fall of water from a faucet can be thought of as an inviscid flow because friction…

A: Given: The distance between points 1 and 2 is 7 cm i.e. z1 - z2 = 7 cm or 0.07 m The diameter of…

Q: Steam flows in a Schedule 40, 6 (in) (Internal Diameter-6.065 in) pipe 1000 ft long, with roughness…

A: Given that  For schedule 40d1  =6 in =6 x 0.0254 = 0.1524 m L = 1000 ft =  10003.28084 =304.8 m m  =…

Q: A converging-diverging nozzle is used to accelerate water at the state of superheated steam. The…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Air (y = 0.075 lbf ft3) is flowing as in figure. If u = 13.9 ft s and the centerline velocity, vc =…

A: Given : Density of air = 0.075 lbf / ft3 Velocity ( V1 ) = 13.9 ft / sec Velocity ( V2 ) = 15.7 ft /…

Q: A 10-cm inner diameter pipe has air flowing through it at 50 m/s at 30°C and 1.6 bar (gauge)…

A: Given velocity of air at pipe inlet ,v1=50m/s diameter of pipe at inlet = 10 cm=0.1 m gauge pressure…

Q: #2: Your boss tells you that water at 68 F is flowing in a cooling tower loop at a rate of 35 gpm,…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: Q2: Tank filled with liquid at a height (ho). The tank's base is connected to a valve. If the valve…

A: given-liquid height in tank=h0 find-height variation with time

Q: Imagine water flowing through a heated pipe which becomes narrower at the halfway point. Which…

A:

Q: Q2) Consider the large tanks system shown in Figure Q2. Determine the level of water in tank 1, ha.…

A: Diameter of pipe at the exit of tank A = 0.03 m Diameter of pipe at the exit of tank B = 0.05 m…

Q: Use Bernoulli’s equation .

A: (a) v = 20.88 m/s(b) v = 1.886 m/s(c) v = 2.5668 m/s(d) v = 1.197 m/sExplanation:

Q: 4.36. A steady-flow water power plant has the following inlet and outlet conditions: Pressure, psig…

A: Given data for steady flow water plant are as follows:   Inlet Outlet Pressure, psig 0 0…

Q: Chapter 5: Water (density is 1000 kg/m) is in the cylindrical tank. When the valve at B is 1)…

A: In fluid mechanics, according to Swiss mathematician and physicist Daniel Bernoulli, the total fluid…

Q: Q1: Air flows in a pipe 10 mm diameter and 120 cm length at 0.25 MPa and 25 °C. if the exit pressure…

A:

Q: For the vertical pipe with manometer attached, as shown in Fig. 2-19, find the pressure in the oil…

A:

Q: A rigid, stationary, short evacuated tank is adiabatically filled with gas from a horizontal,…

A:

Q: 4. (20 points) Water (25°C) flows at 4.5 gpm (gpm is gallons per minute) in the system shown below.…

A: a) flow rates will be same along the pipe assuming no change in density.   1 gpm =0.00006309 m3/s…

Q: 5.40. The tank in Fig. 5.33 is cylindrical and has a vertical axis. Its horizontal cross-sectional…

A:

Q: 3.36 Determine v the velocity V in the pipe if the fluid in the pipe of Fig. 3.15 is: (a)…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Air at static temperature of 300 K and static pressure of 140 kPa flow with velocity 60 m/s. a.…

A: Static temperature of air, T1 = 300 K Static pressure of air, P1 = 140 kPa Velocity, v = 60 m/s

Q: Q.2. Air flows steadily adiabatically through a pipe with a cross-sectional area of 0.002 m?. At the…

A:

Q: A closed tank contains vapor and liquid water at 300 F. The height of the liquid level is 5.1 m.…

A: A closed tank contains the vapor and liquid water. Given data: Temperature of water = 300 0F The…

Q: In a certain gas manufacturing plants, they presented a horizontal tube in which a gas assumed to be…

A: Given data: Initial temperature of N2 = 761.67 0R Initial velocity = 5.6 mph Final velocity = 180…

Q: In a manufacturing plant, there is a pressurized water tank having an orifice at the bottom with…

A: Given data: Diameter of orifice = 0.1 m Height of tank = 5 m Air pressure above the water level =…

Q: velocity distribution of the fluid,

A:

Q: For the conditions and geometry shown in the figure below, calculate the time it takes to completely…

A: Height of tank = 4 m  Diameter of pipe = 0.8 m Diameter of tank = 2 m Fluid is water U1 = 2.6 (1 -…

Q: In a convergent-divergent nozzle where air, at 540 degrees F and 15200 torr enters and flows…

A: Note-Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Shown on the figure below is an open tank that contains water at 10 °C. Incoming water are from the…

A:

Q: Water -Bo C CC14 D 2B.9 Analysis of a capillary flow meter. Determine the rate of flow (in lb/hr)…

A: Diameter of the capillary = 0.01 in Density of the manometric fluid, CCl4 = 1.594 g/cm3

Q: Q2) A cylindrical tank with 2 m diameter has at the bottom sharp-edged orifice (discharge…

A: Diameter of the cylindrical tank =2 m Diameter of the bottom sharp edged orifice, d=5 mm=5×10-3…

Q: (4) Air at 1 MPa and 500°C enters a converging.nozzle, with a velocity of 140 m/s. Determine(a) The…

A: