Carbon Dioxide (CO₂) gas flows steadily in a convergent nozzle. At section 1, flow conditions are T₁ = 400K, P₁ = 500 kPa and M₁ = 0.65. The mass flow rate at exit section (not the same as section 1), is 1.742 kg/sec. The area of cross section A₁

Carbon Dioxide (CO₂) gas flows steadily in a convergent nozzle. At section 1, flow conditions are T₁ = 400K, P₁ = 500 kPa and M₁ = 0.65. The mass flow rate at exit section (not the same as section 1), is 1.742 kg/sec. The area of cross section A₁

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As in the figure, a U-shaped pipe piece in the horizontal plane has water flow. At flange (1) total pressure pressure is 200 kPa, resulting in a mass flow of 40 kg/s to the pipe. At flange (2) , the total pressure is 150 kPa and the mass flow is 30 kg/s from the pipe. At (3) mass flow rate of 4 kg/sec from the section and 6 kg/sec from the (4) section to the atmosphere at 100 kPa pressure is discarded. With relative powers; Determine your Total Rx Ry forces at flange(1) and (2). ***Sections (1) and (2) are close enough ***density of water ??? = 1000 ??/?3 ***kinetic energy correction factor = 1,035 and momentum flow correction coefficient 1,025 *** mass flow = density*flow rate
A point source with volume flow Q = 30 m3/s is immersedin a uniform stream of speed 4 m/s. A Rankine half-body ofrevolution results. Compute (a) the distance from the source to the stagnation point and (b) the two points (r, θ) on thebody surface where the local velocity equals 4.5 m/s.
Air flows in a duct having cross-sectional area A = 0.861 m², flow speed V 10 meters / sec, pressure P = 100 kPa, temperature T = 300 °K. Determine the mass-flow-rate, m(dot) in kg / sec.
Air at atmospheric conditions (101.3 kPa and 20° C) enters the bottom of a 90° conical flowmeter duct at a mass flow rate of 0.4 kg/s, as shown in Fig. 4. It is able to support a centered conical body by steady annular flow around the cone. The air velocity at the upper edge of the body equals the entering velocity. Estimate the weight of the body in newtons 90° -d = 7.5 cm Fig. 4
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A1= 10ft^2, U1=100 fpm, v1= 4 ft^3/lbm. At section 2: A2= 2ft^2, p2= 0.20 lbm/ft^3, U2=120 fpm. Calculate (a) the mass flow rate, and the (b) change of mass stored in system ∆m.
Show work for both subparts as it is a single problem.
Determine the arcing distance of sprinkling installation. Overpressure in chamber A,from which water outflows by nozzles B, is ppA = 80 kPa. Velocity coefficient ofnozzles consider to be Ø = 0.90. Calculate the arcing distance in variants, for angle Ø(inclination of nozzle axis from horizontal line) being 35°, 45°and 55°.
A blower supplies standard air to a plenum that feeds twohorizontal square sheet-metal ducts with sharp-edged entrances.One duct is 100 ft long, with a cross-section 6 in by6 in. The second duct is 200 ft long. Each duct exhausts tothe atmosphere. When the plenum pressure is 5.0 lbf/ft2(gage) the volume flow in the longer duct is three times theflow in the shorter duct. Estimate both volume flows andthe cross-section size of the longer duct.
(6) A nozzle is required to pass 1.5 kg/s of air. The inlet conditions are a zero velocity, a pressure of 350 kPa and a temperature of 425°C. If the air is to expand to 140 kPa, determine the throat area required. Also calculate the exit velocity and exit area if the nozzle efficiency is 95 %. Assume that friction takes place in the diverging part only.
A horizontal air jet with a mass flow rate of (m) and a velocity of (V) strikes the inside surface of a hollow hemisphere. Assume the magnitude of air velocity remains constant ( Vin=Vout=V). Determine the horizontal anchoring force (F) needed to hold the hemisphere in place for the following conditions: m = 4.71 kg/s and V = 20 m/s F F= 11.8 N F=105.9 N F= 47.2 N F=188.4 N
Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m? and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y = 1.333 and Cv= 0.86 kJ/kg K.