Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P observes this speed via radar. The driver of car A is traveling at VA = 127 km/h as it passes P, but over the next 5.8 seconds, the car uniformly decelerates to the speed limit of 100 km/h, and after that the speed limit is maintained. At the moment when A passes P, the police car begins to accelerate at the constant rate of 4.8 m/s² until a speed of 156 km/h is achieved, and that speed is then maintained. Determine the distance s required for the police officer to overtake car A. DA P

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: What does on the lines, 4 & 3 indicate

A: Line 3 in View 2 represents the level at which the plan or top view (View 1) is drawn. Although the…

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: 1⁄6 yard +3⁄8 yard

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: Determine the coordinates of the centroid of the shaded area. y | 25 E 50 60 25 60 70 50. --x 170…

A:

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: ate the centroid of the shaded area. Y 20 mm 45 mm 20 mm L. 54 mm

A: To find centroid

Q: Q1: determaine the coordinates of the centeroid of the shaded area 20 40 50 20 40 30 140

A: The polar coordinate system is a method to calculate points in the system location by proper…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: weétermine the yalue j = 2. Det ermine the Yalue & I with Respecd to centroidal X axis =

A: 1. Value of y¯ Let 1 & 2 be the rectangle and 3 & 4 be the triangle.y¯=∑ay∑a…

Q: Q24. Draw the plan, section and elevation of the given line diagram. W BED KITCHEN 2500x2500 D…

A:

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: Assignment 7.: Draw the Projection (Front View & Top View) of a point "G" which is present on the HP…

A: We will draw the projection of the point G with respect to XY line It will include front view as…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: Name three lines that intersect at point E.

A: Draw the figure. The lines which meets at the point E is the intersecting lines at point E. The…

Q: * .I don't like this," said Ali“ Correct Incorrect

A: The correct punctuation marks for this be like this "I don't like this," said Ali.

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.