t a point in a strained material the principal stresses are 200 N/mm2 (tensile) and 120 N/mm2 (compressive). Determine the normal stress, shear stress and resultant stress on a plane inclined at 30° to the axis of major principal stress. Also determine the maximum shear stress at the point.

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: At a point of a material, the stresses forming a two-dimensional system are shown in Figure Q1. By…

A: To find: (i) The magnitudes of the principal stresses. (ii) The directions of the principal…

Q: Q-1) A company manufactures nails and screws, which possess raw materials 300 units and 360 labor…

A:

Q: The direct stresses at a point in a material are 160N/mm2 (tensile) and 120N/mm2 (compressive).…

A: The principal stresses at any point in a body can be calculated using the formula given below as-…

Q: Determine the principal stresses and the maximum shear stress correspondin the plane stress state…

A:

Q: The stress case at a point of a body is shown on the element below. Determine the principal normal…

A: The principal normal stresses, principal shear stresses, and the directions. Given: The stress in…

Q: 2- The state of stresses at a point are defined as follows. Find the normal and shear stress vector…

A: Given: The point of plane, P(2,1.5,2)

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: v)  A delta strain gauge is attached to the member at point ‘X’ as highlighted in the figure. During…

A: The magnitude of strain at an  angle is given by:εθ=εx+εy2+εx-εy2cos2θ+γxy2sin2θAt…

Q: occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane.…

A:

Q: he forces applied to pulleys are given as shown below. Accordingly, show the stress state at point A…

A:

Q: The figure shows the stresses at a point. Determine the principal stresses and the maximum shear…

A:

Q: The stresses shown on the left below act on horizontal and vertical planes through a point on the…

A: Principal stress is defined as the maximum or minimum value of normal stresses and they act on that…

Q: Determine the normal stress at bar AC. Use diameter of bar AC = 215 mm. B 500 N 2 m -J.- 2 m 451

A: According to the given dataThe diameter of the AC is 215mmWe need to findStress in the member AC

Q: A rubber pad is sandwiched between two steel plates subjected to shear force V = 400kN. The…

A:

Q: Determine

A:

Q: The normal stress exerted on the oblique face of the shaded triangular element is

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: a) In order to determine the principal stresses at a point in a structural member, two strain gauges…

A: Given data as below: Angle θ = 30o Strains in two direction: εx = 455 ×10-6εy = -32 ×10-6 Modulus of…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: The following stress condition is applied on a material: 400 200 0 o 200-300 0 MPa 000 Determine the…

A:

Q: At a point in the cross-section of an engineering component an element is subject to the following…

A:

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: 1. The state of plane stress at a point on a body is represented on the element shown in (a).…

A:

Q: The X- axis strains with oriented angle of the bone surface are shown in table X- axis strain (×…

A:

Q: A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr…

A:

Q: Tsy

A: Given Data⇒ σx=60 MPaσy=50 MPaζxy=50 MPa

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: The principal stresses. Given: The stress in the x-direction is σx=-16 MPa. The stress in the…

Q: The Cartesian components of stress at a point are 0x = 15 Oy = 0₂ = 8, - Txy = 6, Tyz = 4, Txz = 4…

A:

Q: Required information Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y

A: GivenX=16MPaY=48MPa

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: Determine the equivalent state of stress on an element at the same point which represents the…

A: According to the given dataWe need to findAverage normal stressMaximum in-plane shear…

Q: -80 MPa and T = 60 MPa The loading on the component is increased so that stresses are increased to…

A: GIVEN:maximum normal stress=300mpamaximum shear stress=200mpa

Q: In a simulation carried out by a team engineers a state of plane stress in a machine base of a…

A: To find - 1. The principal stresses and the maximum in- plane shear stress acting at the point.…

Q: Bi-axial state of stress at a point is shown below. What will be the value of principal stresses and…

A: From the given figure, σx = 100 MPa σy = 80 MPa τxy = 50 MPa

Q: he stresses shown below act on horizontal and vertical planes through a point on the urface of a…

A: Part a): From the given data, the stresses in the respective directions are identified as, σx=0σy=-6…

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A: