Can you calculate the work done .the forces are non conservativ Yes No

Q: A four-cylinder, 2.4liter engine operates on a four-stroke cycle at3200rpm. The compression ratio is…

A: Given data V=2.4 LN=3200 rpmr=18 cmS=1.06 B Here, V is the volume, N is the speed and r is the…

Q: A double-thread trapezoidal-metric-thread-form screw, which is driven by a motor, raises a nut and…

A:

Q: net heat rejected to reservoir C by CE-2

A: Given data; Carnot engine (CE-1) works between       two temperature reserviors A and B;TA=900…

Q: 2.2 A 2.2-tonne racing car has a wheel base of 2.4 m and a track of 1.4 m. The centre of mass of the…

A: (a) To find: The load distribution on the wheel when the car turns left. Given: The mass of racing…

Q: The large diameter and face of the disk of a multiple disk clutch are 255 mm and 25 mm respectively.…

A:

Q: if the forces are

A:

Q: 3. The pruning mechanism of a pole saw is shown as it cuts a branch S. For the particular position…

A:

Q: METHOD OF JOINTS Determine the forces in the members of the roof truss shown. Indicate whether the…

A:

Q: Problem 1 a Given: F Н Mass of canister: 4000 kg 30 30° Mass of beam BD: 50 kg BỊ Max allowable…

A:

Q: How did you get the summation of forces in each direction?

A: We can easily find the vector form of each force and then consider the sum of all the forces acting.…

Q: In a piston cylinder system, the gas expands from 1.5 m³ to 7.5 m³ with an increase in internal…

A:

Q: 2. Draw the free body diagram of the following situations.

A:

Q: 2.91 The rigid bar AOB is pinned at O and connected to aluminum and steel rods. If the bar is…

A:

Q: The coefficient of friction under block A is 0.30 and under block B is 0.20. Find the acceleration…

A:

Q: You are driving down a highway on a sunny 7°C, fall day. The sun heats the 1m², flat, steel hood of…

A: Given:The temperature of the sunny day, The area of the flat, steel hood of the car, The temperature…

Q: 3. If block A weighs 200 N and block B weighs 300 N. Compute the acceleration of block B and the…

A:

Q: Write the equation to calculate the work done by an axial force?

A: Work: Work is defined as the multiplication of the axial force on the body and displacement…

Q: Why isn’t the force in “CE”= 10root5, because 10^2+20^2=10root5 and not 10root2.

A: Given: find the force in member CE.

Q: Determine the reactions for the loaded beam as shown below. Neglect the weight of the beam. 120 lb…

A:

Q: A body floats half and submerged in a certain liquid (s.g. = 1.25) and has a weight of 500 kN.…

A: The weight of the body will act downward and the buoyant force will act upward.

Q: A mass m of helium gas is in a container of constant volume V. It is initially at pressure P and…

A: Given:- initial condition, m1 = m Pressure, P1 = P Temperature, T1= T And final condition as, mass,…

Q: Knowing that the tension in rope AC is 425 N, determine the resultant of the three forces exerted at…

A:

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

A:

Q: Dining tables are made up mostly of a wooden frame and a table top by a manufacturer. Table lists…

A: To find : Determine the economics advantage of the best alternative  Given :    description of…

Q: , Given the Truss as shown below with 0=45°. Using Method of Joints, determine the forces at the…

A: Given: The Truss as shown below with (thita=45°). Using Method of Joints, To find: The forces at the…

Q: Determine the reactions at points A. B and C due to the self-weight of the cylinders. The…

A: We have R1 = 6.1 m R2= 4.2 m R3 = 10.2 m  W1 = 51.1 N W2 = 35.3 N W3 = 123.8 N L = 25 m

Q: 6. A nozzle is a device that converts fluid thermal energy, enthalpy into kinetic energy. The…

A:

Q: 3. A horizontal pipe gradually reduces from 300 mm diameter at section 1 to 100 mm diameter at…

A:

Q: 50 KN/m Determine the vertical deflection at the free end and the slope at the left support of the…

A:

Q: THREE IDENTICAL CYLINDERS ARE STACKED AS SHOWN IN THE FIGURE. FIND THE MINIMUM COEFFICIENT OF…

A:

Q: Equilibrium of Force Systems Q11) Find the reaction moment at the built-in support at A due to the…

A:

Q: It equal and opposite forces applied to a body tend toelongate it, the stress so produced is called…

A:

Q: (a) Plot distance versus time using rectilinear axes. (b) Plot distance versus time on log-log…

A: We need to consider the label of rectilinear axes to draw the graph. Let's consider the x-axis…

Q: DETERMIEN THE SMALLEST VERTICAL FORCE P REQUIRED TO PUSH THE WEDGE BETWEEN TWO IDENTICAL CYLINDERS,…

A:

Q: A homogenous bar AB weighing Wis supported by a ball and socket joint at A and two cables attached…

A: Given data, Coordinates of A = (0, 0, 0) Coordinates of B = (-5.1, 0, 4.3) Coordinated of C = (4.3,…

Q: A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.