2. Draw the free body diagram of the following situations.

Q: What is the significance of Burger's equation? Elaborate briefly.

A: The degree and direction of the lattice deformation associated with a dislocation in a crystal…

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: Question 11 1 Z Miller index: Write out Miller Index for the plane and direction. Miller Index:

A: Write out Miller Index for the plane and direction.

Q: How can we determine the maximum displacement?

A: The expression for the displacement of the simple harmonic motion is given by, Here, x is the…

Q: Give the definition of Poisson's ratio with an example?

A:

Q: Compute the temperature difference if the inside furnace temperature is 608°F and the outside…

A:

Q: For a particular centered process, you estimate Pp = 0.90.  What is the estimated ppm defective for…

A: Given, Total number of defective items in a sample size,Pp=0.90To calculate-PPM defective for this…

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: TF 40k 3) T=300k Calculate and for 912, 913 enclosre (Wn?) 923 the

A:

Q: How is the shear flow, measured?

A: Shear flow: The shear flow in solid mechanics is a terms on multiplication with thickness which…

Q: What will be the occerelalion at point L if theuniform KL bor is left horigontal. 2m Support…

A: Given, The mass of the bar, m=25 kg The length of the bar, L=4 m

Q: Example 4: Find the general solution! y" - x ²³ + 1 = 0 -

A:

Q: Find the welouty Slay A=2.1m2 of S. - २० ms %3D

A: Given data : Area of channel A=2.1 m2 Discharge through channel Q=20 m3/s   To find : Velocity of…

Q: A certain type of cans are formed on a machine by spinning them from cardboard stock and attaching a…

A: Given \ Sample size N=50 Total number of samples is M=30 Table1: Number of nonconforming cans in a…

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: Industrial pipes Expansion joints are fragile elements and therefore should be avoided…

A: The objective of the question is to understand when to use expansion joints in industrial piping…

Q: why is the kinetic energy for this problem only rotational? Thank you!

A: Given: Motion of the point A will be in horizontal direction and the motion of the point B will be…

Q: 150 N r= 25 mm Calculate the equivalent moment at O, taking into account the values given in the…

A:

Q: How the forced vibrations can arise?

A: When a body vibrates due to the influence of external periodic force, then this type of vibrations…

Q: Is the Hotelling Rule applicable to oil?

A: Hotelling's hypothesis, often known as Hotelling's rule, states that nonrenewable resource…

Q: Given data : Force%33 N Work done-12 J Find Displacement

A: Given data : The value of work done=12 J The value of force applied=3 N   To find : Displacement

Q: ) Given: h,- 3620 k/Ya, V. : 45mls ト、 V, - 75 mls Vq 120mls (caleulate the work Dore by seam) Stea…

A: Given data,  h1 = 3620 kJ/kg  h2 = 2800 kJ/kg  V1= 75 m/s  V2= 120 m/s  Assumptions-  z1=z2 and heat…

Q: 5. Use superposition to find the deflection of the free end of the cantilever shown below: w lb/ft 2…

A:

Q: What is the advantage in casting turbine blades that have either highly aligned grain boundaries or…

A: Turbine blades are manufactured by casting by containing superalloys in them. These superalloys have…

Q: Shear modulus is similar to O work hardening O percent reduction in area O Avogadro's number O…

A: Shear modulus When a force is applied parallel to one of a solid's surfaces while an opposing force…

Q: wouldn't your last equation be Q/A= H (Tair-Tsurface)

A: Required:The explanation on the equation of heat flow per unit area, QA=h×To,surface-Tair

Q: why are you squaring the velocity in the eq

A:

Q: Prove that the most efficient triangular section is the one with a 90degree vertex angle.

A: To prove that the most efficient triangular section is with a vertex 90° : consider a triangular…

Q: 4. This diagram shows the front-end of a machine that has a bucket at the tip. The total weight of…

A: solution Step 1 -:                Draw FBD of bucket and analyze tanθ =0.32.5θ=6.843°sin θ =0.12cos…

Q: For crank slider, L,=40mm; L,= 120mm; Offset =-20mm and d=100mm and . Find the possible value of 0,…

A:

Q: 4. Briefly describe die casting process and name 2 types.

A: die casting method  the die casting are also known as pressure die casting and are defined as that…

Q: Defoomine max: ofeay sforess ?

A: Given: state of plane stress at point is:  σx=220 MPa  σy=100 MPa   ζxy=130 MPaFor the data given,…

Q: From well logging process we got the following records: GR-50, NPHI= 9%, Ph 2.23 gm/c, At- 70…

A: Given dataBulk density ρb = 2.23gm/cc∆t = 70μsec/ft∆tma =47.5μsec/ftGRmax = 150GRmin = 50TD =…

Q: Choose forming and generating operation 2 po Work Work Threa dsad dsa Generated surface Work Work…

A: This is taper turning

Q: Q2:-Choose the Correct answer. (1):- Grain growth in size (recrystallization) occurs at a-…

A: Keeping a note as per our company guidelines we are supposed to answer only the first 3 subparts.…

Q: :. V = 2k k-1 -R(T.-T) Approve that?

A:

Crystalline Imperfections

The crystalline imperfections are described as the geometrical defects in the crystal due to incorrect arrangement of atoms, impurity, vacancy, and many more. It is not possible to achieve a perfect or ideal crystal, practically.