Can we use this pump to supply water to anelvation 35 meters above? Explain your answer.WizzWJSW/10MPOWQ 5 - 70POWERMARKWATER PUMPcontinuousdutyS/NW11110199I/min H 30 ÷ 10POWERMARKHmax 35 mQmax 80 l/min1-Mot lv. 220Hz 60 3450 min-1kW 0.75 HP 1 In 3.8 A 950 WmaxC 16 μF VL 450 V I.CL B IP 44CEAmthermallyprotectedPOWERMARK

Given: Water Pump with manufacturer specifications

Answered: Can we use this pump to supply water to…

Engineering

Mechanical Engineering

Can we use this pump to supply water to an elvation 35 meters above? Explain your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A manufacturer states that their gear pump requires 0.85 hp to pump 9 gpm of oil (sg=0.90) with a…

A: The flow rate of the oil is, Q=9 gpm. The specific gravity of the oil is, SGo=0.90. The total heat…

Q: o be pump from a reservoir with a temperature of 32oC at sea level. Friction loss at suction is 0.3…

A: pressure @sea level = 101.3 KPa Psat = 4.798 kPa datum difference = 2.45 friction loss = 0.3 m

Q: Discuss with neat diagram the pump flow characteristics if pumps are used in : (i) Parallel (ii)…

A: When pumps are connected in parallel, the total discharge is equal to the sum of the flow from each…

Q: PLEASE BOX YOUR ANSWERS A centrifugal pump is used to pump water at 30°C (S.G. = 0.996) from a…

A: Given: diameter of pipe, d=24 mmfriction factor in pipe, f=0.022(NPSH)R=2.2+0.958v2 metersSpecific…

Q: Q1) It is desirable to use the 32-in pump of Figure below at 1170 r/min to pump water at 60°F from…

A: Given data: The friction factor is f=0.00725 The ID of pipe is d=16 in

Q: A tank 1.5 m stands on a trolly and is full of water. It has an orifice of diameter 0.1 m at 0.3m…

A: Given:h=1.5 md=0.1 mCd=0.6

Q: Explain why some pump performance curves may lead tounstable operating conditions.

A: For the unstable operating condition, the distortion blade angle, vane angle or any king of dent or…

Q: There are three main categories of dynamic pumps. List and define them.

A: Dynamic pumps are typically the main pumps generally used for large flows with lower pressures. They…

Q: A pump lifts water between two reservoirs, the diference of elevation is AH= 25 m, through a ductile…

Q: (a) Two vertical cylindrical tanks of 3.00- meter and 2.00-meter diameter containing water are…

Q: Q5 (a) Discuss the primary difference between positive displacement pump and dynamic pump. Give…

A: Both the pumps (positive displacement and dynamic pump) have their own benefits. The major…

Q: The circular cross section tank with a height of (0,762 +0,262 +1,562=2.4+3*0,062) m and a radius of…

A: Given data: a = 6 and b =2 Height of the tank, h = (0.7(ab) + 0.2(ab) +1.5 (ab)…

Q: You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow…

A: Given Data⇒ Total manometric head(h)=11 m Flow is Q=19LitsSInce 1Lits=1000m3shenceQ=0.019m3s The…

Q: The performance data for a centrifugal water pumpare shown in Table P14-31 for water at 20°C…

A: Given that :- Volume flow rate (Lpm) =12 Firstly change into m^3 12 L/min = 12 × 10^-3 (m^3) /60…

Q: 3- Discuss the siphon process and what benefit of it?

Q: A farmer owns an 8-hp engine. He wants to use it to pump water from a 50-ft deep shallow tube well…

A: To find: The size of the pump. Given: The power of the pump is P=8 hp550 lb.ft/s1 hp=4400 lb.ft/s.…

Q: The answer is (7.095 hrs.). The problem is; If the orifice diameter is 1 cm and it's a vertical…

A: Given, Orifice diameter, dc=1cmHeight of the tank,h=4mRadius of cylinder,r=1mTo…

Q: A cylindrical well is 2m in diameter and 12 m deep. If there is 3m of water in the bottom of the…

A: Given that: Diameter of the well = 2 m Depth of the well = 12 m Depth of water inside the well = 3 m…

Q: →Water is being pumped from a reservoir with water surface elevation of 12 m to another reservoir at…

Q: 1. What approximations, if any, can you make from the statement that the diameter of the tank is…

A: From the given problem it has been stated that diameter of tank is larger than diameter of nozzle.…

Q: A 2-kW pump is used to pump kerosene (p = 0.820 kg/L) from a tank on the ground to a tank at a…

A: Given,Power P = 2 KW = 2000 WDensity of kerosene = (rho = 0.820 kg / L)Elevation differences between…

Q: For transferring of water, a pump is installed in the height of 3 m above the surface of the water.…

A: hsp=Pρg=100kpa1000×9.81=10.19hs=3mhf=4mhvp=Pvρg=10kpa1000×9.81=1.019

Q: In a pumping system handling water, the surface level of water in the open suction tank is 3m below…

A: The suction level below the pump center is hs=3 m. The delivery level above the pump center is hd=21…

Q: when pumping water from a lake to a lake above It gives 7.5 kW of energy to the water. your lakes…

Q: A proposed hydropower plant to be built using a reservoir with a typical head of 18m and estimated…

Q: If a pump with a manometric head of 12 m is designed to deliver a flow rate of 7500 liters / minute.…

A: Given: Manometric head (Hm)=12mFlow rate=7500L/minPump speed=1800rpm

Q: The water needs of a small farm are to be met by pumping water from a well that can supply water…

A: Given Data The flow rate of the water is:Q=5 L/min The water level in the well is:hw=13m The…

Q: air pressure above the water is . The required NPSH of the pump is 8.2 m. The suction pipe has a…

Q: For the system shown in the Figure, Reservoir I has a water depth of 7 m and Reservoir 2 has a water…

A: INTRODUCTION : The head losses occur in pipes when the area of the crosssection occurs in the pipe…

Q: review the example. Thank you very much Question : Determine the power required (Watts) to drive…

A: Given:Speed of the pump, N=1 rpsDischarge of oil, ρ=850 kg/m3Flow rate, Q=375.3 gpmbore, d=250…

Q: Three pipes are connected in series with properties given as: for pipe A, L= 300 m, diameter = 15…

A: Given: The length of pipe A, LA = 300 m The diameter of pipe A, dA = 15 cm = 0.15 m The length of…

Q: According to Figure 1, information given de= 500mm, Ve= 7.0 m/s, h= 5.0 m and PB= 105 kPa.…

A: i. The pump head is 41.2 m. The discharge of water is 1.37 m3/s. The pump power is 555.5240 kW.…

Q: .Water is stored in a reservoir 5 m deep and 100 m in diameter. It is pumped through a 0.3 m…

A: To determine the maximum height to which the water can be raised.

Q: Water is delivered from a truck (shown in Figure 1b) to a maximum 18m height above the hydrant. It…

Q: I have a question from my fluid power enginneering class. The question was, standard hydraulic oil…

A: Given: Pressure at the pump outlet is 10 psi. Height of uphill is 100 ft. Flow rate is 10 gpm.

Q: calculate The pump efficiency if the total area equal (A=0.0032m) and (V=1.5m/s) when the total…

Q: Water is to be pump from a reservoir with a temperature of 32°C at sea level. Friction loss at…

Q: (d) What influences the pressure developed by a pump when it is operating, and also the maximum…

A: (d). What influence the pressure developed by a pump when it is operating,and also maximum pressure…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Can we use this pump to supply water to an
elvation 35 meters above? Explain your answer.
Wizz
WJSW/10M
POW
Q 5 - 70
POWERMARK
WATER PUMP
continuous
duty
S/NW11110199
I/min H 30 ÷ 10
POWERMARK
Hmax 35 m
Qmax 80 l/min
1-Mot lv. 220
Hz 60 3450 min-1
kW 0.75 HP 1 In 3.8 A 950 Wmax
C 16 μF VL 450 V I.CL B IP 44
CE
A
m
thermally
protected
POWERMARK

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A square bottomed tank measures 25*25*160cm and is positioned with the bottom of the tank 1m above sea level and at 20degreesC. The tank is 90% filled with water and 10% air. A water inlet enters the centre of the tank of 10mm diameter, and no other inlet or outlet is open within the tank. A pump drives water at a starting rate of 450ml/min at 0 Pa lowering to 350ml/min as the pressure increases to 800 kPa. The pump and tank are connected by a 10mm diameter pipe with k=0.15 for all fittings and tubing. It should be assumed this is the maximum flow and pressure provided by the pump. The pump will stop instantaneously once the pressure reaches 800kPa. The relationship between flow and pressure from the pump should be assumed linear. What will be the volume of compressed air inside the tank and how long will it take to fill?
i need the answer quickly
strictly don't copy. Urgent
Explain also
ANSWER ASAP PLEASE
Pls help ASAP.
A small centrifugal pump is used to pump 300C water at the rate of 6 L/s with ahead of 44.54 m. If the diameter of the pump is 20 cm and operate at 1200 rpm,determine;(i) head coefficient,(ii) capacity coefficient, and(iii) power coefficient.
A vane pump with a volumetric efficiency of 82% and amechanical efficiency of 80%. Calculate the mechanical power required (Hp) to drive it if the working pressure is 1800 psi and a flow rate of 20 gpm? Answer:32Hp
In Fig. is shown a plot of pump net head as a function of pump volume flow rate, or capacity. On the figure, label the shutoff head, the free delivery, the pump performance curve, the system curve, and the operating point.
On a trip to the beach (Patm 1 atm or 101.3 kPa), a car runs out of gasoline and it is necessary to siphon gasoline from a Good Samaritan's car. The siphon is a hose with a small diameter and to start the action it is necessary to insert one end into the tank full of gasoline, fill the hose with it through suction and then put the other end in a can that is placed under the tank level. The difference in pressure between point 1 (on the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the highest elevation to the lowest. In this case, point 2 is located 0.75 m below point 1, and point 3 is 2 m above 1. The siphon diameter is 4 mm and friction losses in it must be ruled out. Determine: a) theminimum time to bring 4 L of gasoline from the tank to the can and b) the pressure at point 3. The density of the gasoline is 750 kg / m3.
Three pipes are connected in series with properties given as: for pipe A, L= 300 m, diameter = 15 cm, for pipe B, L= 400 m, diameter= 20 cm and for pipe C, L= 600 m, diameter= 25 cm. The Manninbg's coefficient of the three pipes n= 0.011. If the total frictional losses is 5 m, excluding minor losses, determine the amount of water flowing through the pipe system. (WITH FREE BODY) CHOICES: a.30 L/s b.35 L/s c.25 L/s d.20 L/s
A hydraulic turbine receives water from a reservoir of 50 meter above it. What is the minimum flow rate in kilograms per second to produce a steady turbine output of 30 MW