Q2/ Actual Rankine cycle, has the following specifications:Boiler pressureTurbine inlet temperatureCondenser pressureTurbine efficiencyPump efficiency160 bar600 °C0.08 bar0.90.85130 kg/sSteam mass flow rateCalculate: Work net (kW), heat addition (kW), and thermal efficiency.

Answered: Image /qna-images/answer/4be93f5e-a9f5-47bf-a561-f5bf17bd7692.jpg

Answered: Calculate: Work net (kW), heat addition…

Engineering

Mechanical Engineering

Calculate: Work net (kW), heat addition (kW), and thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ Ideal reheat cycle, has the following specifications: Boiler pressure is 200 bar and Condenser pressure is 0.22 bar and Reheat pressure is 60 bar , Turbine inlet temperature is 500 C and Reheat temperature 480 C Calculate: quality at turbine exist, thermal efficiency, and steam rate.
Please draw the TS diagrams of the cycle. Subject: Thermodynamics (Rankine Cycle)
Q1. Sketch T-s diagram for Rankine cycle with clear label for the following condition: Condensate pressure = 100 kPa • Boiler pressure = 3 MPa • Inlet temperature to the turbine = 350°C Determine thermal efficiency of the cycle. ANSWER
i need some one explian the TS digram Rankine Cycle please don't use google
Write legibly, provide manual step by step solution, and diagram for below given problem. A superheat steam Rankine cycle has turbine inlet conditions of 17.5 Mpa and 530 C expands in a turbine to 0.007Mpa. The turbine and pumps polytropic efficiencies are 0.9 and 0.7 respectively, pressure losses between pump and turbine are 1.5MPa. What should be the pump work in KJ/kg? A. 17.3 C. 37.3 B. 27.3 D. 43.4
I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P = Ps= Preheal Pump Condenser Low-P turbine Figure (2.7 a) High-pressure turbine Reheating Low-pressure turbine
Pa Complete the table given below for a closed system undergoing a cycle. Coet Wet Process Wot kJ AUKJ 1-2 21 11 2-3 14 -8 3-4 -5 4-1 4. 6.
Q1/ A gas turbine cycle has the following working parameters: - The pressure of air entering the compressor at( 1 bar) The compressor ratio=6 - Max. Temperature of cycle (1000°k) and Min. temperature (288 °k ) -Nc= 0.85 . NT=0.9 Find :1) Nth 2)Net work per kg
Air enters an ideal gas turbine cycle at 1 bar and 27 C. The maximum temperature in the cycle is 727 C. Find the cycle efficiency for a compression ratio of 10. [Ans.: 0.482].
please answer a question bartleby !!!
Please need within 1 hour Thankyou.
A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |Wnetl. e. Determine the thermal efficiency (n) 6 MPа, 550 °C Boiler 6 MPa w, (turbine) |mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % w, (pump) 3 4 Condenser 50 КРa 50 kPa Working fluid: water