calculate the Maximum Positive Shear in kips if the given 30kip concentrated load and 2kip/foot uniform load from the figure are both replaced by 39kips and 18kip/foot respectively. Express your answer in 2 decimal places.

Q: The cross-sectional dimensions of a beam are shown Below (a) If the bending stress at point K is…

A:

Q: 1) A straight hollow shaft is fixed at one end and free at the other end. The shaft is made of…

A:

Q: A cantilever beam BD rests on a simple beam AC as shown below. Both beams are of the same material…

A: It can be solved using solving for moments along both the axis.

Q: swer asap. Thank y

A: i  angle of twist criteriaWE KNOW FOR SERIES ϕAC=ϕAB+ϕBCϕAC=TLABGJAB+TLBCGJBC1.25°×π180°…

Q: OV ko T | B P · C a b c F D + W 11¹ h

A:

Q: The internal shear force V at a certain section of an aluminum beam is 11.3 kN. If the beam has the…

A:

Q: he figure. Each spring consists of 23 turns eter wire having a mean diameter of 6 in. e maximum load…

A: To given  thatNumber og turns, n=23Diameter of spring,d=34in=0.75inMean diameter of…

Q: Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi B L1 L2

A:

Q: The individual forces P act on the simply supported beam made of I profile, the dimensions of which…

A: Support reaction at A and B =Pmaximum shear force in the beam span V=Pmaximum bending moment will…

Q: From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.35°.…

A:

Q: A C 10 kN G BD F H K 8 @ 2m = 16 m MN 15 kN 5 kN P 4.0m

A:

Q: Mechanics Rate will be given! Please write the complete solutions legibly. Box the final answer in 3…

A:

Q: The Cantilever truss in figure below is hinged at D and E. Find the force in each member. 1000 lb B…

A:

Q: UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer…

A:

Q: 9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the…

A:

Q: For the frame shown above is constructed out of circular tubes for both the beam and column.  It has…

A:

Q: The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B.…

A:

Q: y 150 mm 150 mm B 400 mm 600 mm A

A:

Q: For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to…

A:

Q: 3 m Reactions @A Ic Ax = A₁ = MA = Internal Loads @C V = M= N = 3 m ts) s) 8 kN/m 3 m Force lagram…

A:

Q: The system shown is in static equilibrium and motionless. All joints are ideal. • The origin of the…

A:

Q: 2. Determine the reactions at the supports and forces at hinge B acting on member CBA and the…

A:

Q: double tee cross section is used for the beam shown below.  Assume the following lengths and loads:…

A: Given: a = 15ft b= 8 ftc= 13ftP = 22000 lbQ =7000 lb   bending stress equation MI =σyM = max bending…

Q: For the beam shown in the figure below, find the maximum tensile and compressive flexural stresses.…

A: step 1-

Q: A double tee cross section is used for the beam shown below. Assume the following lengths and loads:…

A: Moment of inertia (Iz) = 110 in.4 Determine the maximum tensile bending stress.

Q: Note: Please show all of the free body diagrams used and also show the complete solution. The beam…

A: As per company's guidelines we can only answer first question.  Kindly post other questions as…

Q: Problem No.3 A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter.…

A: solution Given shaft diameter d=104mm allowable shear stress ζ=48Mpaallowable angle of twist θ=2°…

Q: Thanks for answering

A: The objective of the question is to calculate the location of the centroid, the second moments and…

Q: Shown in the figure is a loaded platform with corresponding rectangular cross section. Determine the…

A: Asked: To determine the normal stress (Compressive/Tensile) at F.   Given: Cross-section at F: 24…

Q: H.W.2: Find the maximum applied load (P) that can be applied on the rectangular beam with dimension…

A: Given a simply supported beam, spanning = 12m Carrying two point loads at 4m from either sides of…

Q: For the structure and loading shown below, find the lateral deflection at the top. Use E = 29,000…

A:

Q: An aluminum bar having a cross- sectional area of 0.5 in2 carries the axial loads applied at the…

A: Given data:- The given cross-section area, 0.5 in2 The value of E is, 10×106 psi As per the given…

Q: Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN,…

A: Given- Stepped bar- Axial load P=1 KN, Cross sectional areas A1=100 mm2, A2=60 mm2, Young's modulus-…

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

A: As per company's guidelines we can only answer first three questions.  Kindly post other questions…

Q: C a a 캬 b a

A: Given Permissible stress = 300 N/mm2Concept-Using the moment of inertia of I-section =…

Q: Determine the magnitude of the pin force at A. Assume W = 640 Ib, a = 3.5 ft, b = 2.6 ft, r = 8 in.…

A: Step 1

Q: Draw the shear and bending moment diagram for the beam. If the cross section of the beam is as shown…

A:

Q: 500 mm Al A 400 kN/m 0.5 m B 40mm 0.5 m Fe с

A: Given data,  External dia of two posts = dext = 40mm Distributed load = 400 kN/m  Height of…

Q: QUESTION 3. A simply supported beam, having notches on its surface, is subjected to a triangular…

A: factor of safety F=1.5 varying loading zero at mid and w0 at ends ∑fy=0;    sum of support…

Q: The principal stresses are incorrect but the maximum shear stress is correct.  What are the two…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.