Answered: Calculate the water pressure at the… | bartleby

Related questions

Question

Pressure = weight density x depth
Part A
Calculate the water pressure at the bottom of a 70-m-high water tower.
Express your answer with the appropriate units.
P= Value
Submit
μA
Provinia Faarthank
Request Answer
Units
?

Expert Solution

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

So I'm just making sure I had the work done correctly I know the unit has to be in kPa but I wasn't sure if it would be just 20kPa or if it would be 20,000kPa
A scale reads 102 N when a piece of aluminum is hanging from it. What does it read when it is lowered so that the aluminum is submerged in water? The density of alluminum is 2700 kg/m3 Use g = 9.8 m/s2 Calculate answer to two decimals.
Water enters a house through a pipe with an inside diameter of 2.5 cm at an absolute pressure of 4.5 x 10^5 Pa. A 1cm pipe leads to the second floor bathroom 4m up. The flow speed at the inlet pipe is 2 m/s find the flow speed, pressure, and volume flow rate in the bathroom
I need help with this question
A beaker is filled with an unknown liquid up to a depth of10.00cm. The gauge pressure at the bottom of the beaker is measured to be 1540.00PaWhat is the density of the liquid contained in the beaker? 1571.43kg/m^3 <---- ans to 1, help with following question. Does the gauge pressure at the bottom of the beaker increase more if a student adds a 15.00cm layer of oil (?oil=895 kg/m^3) or of the unknown liquid? a. The gauge pressure increases more with the addition of the unknown fluid. b. The gauge pressure increases the same with the addition of either fluid. c. The gauge pressure increases more with the addition of the oil. d. Impossible to tell.
1. The 3 cm diameter water pipe in the figure splits into two 1 cm diameter pipes. All pipes are circular and at the same elevation. At point A, the water speed is 2 m/s and the gauge pressure is 50 kPa. Assume Pwater = 103 kg/m³. The viscocity of water n = 0.001 Pa.s Cross-section view of pipe AO B a) What is the water speed at point B? m/s b) Calculate the Reynolds number, Re, for the fluid flow in region A and region B. Re in pipe A = Re in pipe B = c) The flow is at point A and at point B.
1st question only please?
A scale reads 97 N when a piece of aluminum is hanging from it. What does it read when it is lowered so that the aluminum is submerged in water? The density of alluminum is 2700 kg/m3 Use g = 9.8 m/s2 Calculate answer to two decimals.
Water towers store water above the level of consumers for times of heavy use, eliminating the need for high-speed pumps. How high (in m) above a user must the water level be to create a gauge pressure of 2.92 x 105 N/m²? Xm + Viewing Saved Work Revert to Last Response Submit Answer.
Determine the pressure at the bottom of a drum 0.50m deep and filled with water.
Determine the flow rate (in cm³/s) in the small pipe shown in the figure given a diameter D of 5.0 cm. 0.1 m 0.2 m D
23. The figure shows a pipe full of water, where vi-3.00 m/s, h₁-3 m, P₁ is the gauge pressure of 5.00 x 10 Pa at the same location. Calculate the gauge pressure of the pipe's higher (3) section if A-2A and P2-3.25 x 104 Par AL h₁ Figure 14 P₁ A ha [Dm]

SEE MORE QUESTIONS