Calculate the tolerance if the maximum limit is 97.45 mm and the minimum limit is 96.99 mm.

Q: A metal disc of 20mm diameter is to be punched from a sheet of 2mm thickness. The punch and the…

A: Given operation is blanking operation. Blank operation  = D = 20 mm Sheet thickness = t = 2mm…

Q: On the toleranced rectangle below, what is the tolerance within which the to be parallel to the…

A: Parallel symbol describes a parallel orientation of one reference feature to a datum surface or the…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: If the main scale reading(mm) and vernier scale reading (division) are 11 and 15 respectively for a…

A: main scale reading = (MSR) = 11 mm vernier scale reading (VSR) = 15 mm no of division = 20

Q: Which one of the following is the radial distance of a tooth measured from the pitch circle to the…

A:

Q: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1)…

A:

Q: Calculate the following slip gauges assemble to 100.115 mm. Use the of 1st, 2nd, 3nd & 4th to give…

A: (A) lets continuing with the slip guage' 100.115 - 1.005=99.11 99.11-9.11=90 90-90=0

Q: There are two different indicated drawings in Fig.1. (1) Judge the tolerance principle they used…

A:

Q: Tolerance note is given by: .XX ± .01 cm and .XXX ± .001 cm. What is the tolerance for a feature…

A: Given:- Tolerance note .XX ±.0.1.XXX ± 0.001To find:- Tolerance for a feature

Q: In the following figure, add the largest equal coordinate tolerances so that if two parts are…

A: Maximum distance between mating hole centers, d = 0.5 mmLets assume the equal coordinate tolerance…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Determine the relative roughness of cast iron pipe with inner diameter 3.1 inches. Your answer…

A: Given Internal Diameter (D) = 3.1 inches                                    = 3.1 * 25.4 mm…

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: 2. The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"

A: To find:  sketch a feature control frame that matches the description given.: 2. The cross-sectional…

Q: Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k…

A:

Q: Problem (2): Determine tolerance value and limit dimension of the rod which a diameter is Ø47 mm…

A: Given data: The diameter of the rod is d = 47 mm. The limit deviation is D = 47.6 mm.

Q: Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus)…

A: Firstly, we get to know about Measured value and True value: Measured value: The value which is…

Q: f the metric micrometer to a precision

A: 5.332

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A: We need to find the center of mass of the system . To find center of mass of system, we have to…

Q: The motor produces 30kW to the A-36 steel solid shaft at a frequency of 20HZ. The shaft is 70mm in…

A: Given data as per question diameter of shaft (d)=70 mmω=20 Hz=20×6.28=125.6 radsPower developed by…

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: Identify which is the GO plug and which is the NO GO.   Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: Please write the definitions for tolerances, draw the hole shaft basis diagram. Write down different…

A: Definition of tolerances: Tolerancing is genuinely like made tongues. It has its own norms. In a…

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: What is the width of the vee groove?

A: In the given drawing the width of the groove is in the side view. The width of the groove is showing…

Q: A slip gauge setting height 50.14 mm is observed when a sine bar of the length 147.32 mm is used…

A: Slip gauge angle

Q: What type of form tolerance is shown in this figure?   Flatness Straightness Cylindricity…

A: Given data : Figure

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: required punch diameter ?

A: Given data;   A meatal disc is to be punched having following data,i.e,  Diameter,d=30 mm…

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: The micrometre is a direct measurement device with a least count of 0.01 mm, that has 20 divisions…

A: