Calculate the surface tension for the solid/water interface (sw) if the droplet adopted a shape with the contact angle 60°. What is the surface tension for the solid/water interface (Ysw) if the droplet spreads over the surface? Estimate the average displacement of a molecule of a surfactant over the surface of the droplet within 0.001 s if the diffusion coefficient is 10-1⁰ m² s-1.

Calculate the surface tension for the solid/water interface (sw) if the droplet adopted a shape with the contact angle 60°. What is the surface tension for the solid/water interface (Ysw) if the droplet spreads over the surface? Estimate the average displacement of a molecule of a surfactant over the surface of the droplet within 0.001 s if the diffusion coefficient is 10-1⁰ m² s-1.

Chemistry: Principles and Reactions

8th Edition

ISBN:9781305079373

Author:William L. Masterton, Cecile N. Hurley

Publisher:William L. Masterton, Cecile N. Hurley

Chapter9: Liquids And Solids

Section: Chapter Questions

Problem 79QAP

See similar textbooks

Similar questions

Examine the nanoscale diagrams and the phase diagram for Question 112. Match each particulate diagram (1 through 7) to its corresponding point (A through H) on the phase diagram.
21) (5 points) The surface tension of ethanol (CHCH2OH) is 0.022 J/ m2 and the surface tension of hexane (CH3CH2CH2CH2CH2CH3) is 0.0179 J/m2. Define surface tension and explain why the values for the listed molecules are different.
18)
Need help with this question. Thank you :)
The vapor pressure of water changes with temperature, as shown here T(C) P (torr) 21 18.7 22 19.8 21.1 224 238 252 26:7 28.4 30.0 31.8 23 24 25 26 27 28 29 30 Bexi Constants | Poriodic Table A student designs an ammeter (a device that measures electrical curent) that is based on the electrolysis of water into hydrogen and oxygen gases. When electrical current of unknown magnitude is run through the device for 3.50 min, 13.0 mL of water-saturated H₂(g) is collected The temperature and pressure of the system are 25 C and 715 torr. Y Part A How many moles of hydrogen gas are produced? Express your answer numerically in moles View Available Hint(s) ΤΕΙ ΛΕΦ 4 2 Submit Part B Complete previous part(s) Pearson mol
Determine the enthalpy of vaporization at 343.15 K for water. (Note: The heat of vaporization for water is known to be 40.79 kJ mol-1 at 273.15 K, the Cp of water (Liq) was determined to be 85.6 J K-1 mol-1 and the Cp of water (solid) was to be 54.35 J K-1 mol-1). Use the reaction below and give your final answer in kJ mol-1. H2O(solid, 273.15 K, 0.1 atm)--------H2O(liq, 273.15 K, 0.1 atm)
Sulfur exhibits two solid phases, rhombic and monoclinic. Use the accompanying phase diagram for sulfur given below to answer the questions that follow. (A). How many triple points are in the phase diagram? (B). What phases are in equilibrium at the topmost triple point? (C). How many phase transitions are there when rhombic sulfur at 1 atm and 80°C is heated to 500°C at constant pressure?
Sketch the phase diagram of the NH3/N2H4 given that these two compounds do not react with each other. NH3 freezes at -78.000C while N2H4 freezes 2.000C. The eutectic is formed when the mole fraction of N2H4 is 0.07 and the eutectic melts at -80.000C. Label all the regions in the phase diagram and indicate which species are present and in which physical state.
The heat of fusion of Hg at its normal melting point of -38.9°C is 2.82 calg^-1. The densities of solid and liquid mercury at 1 atm and at that temperature are 14.193 and 13.690 gcm^-3, respectively. Find its melting point at 200 atm.
1. Supercooled water can exist, but it has a higher chemical potential than solid ice below the normal melting point of ice. Calculate the amount by which the chemical potential of supercooled water exceeds the chemical potential of solid ice at 1.00 atm and - 5.00 °C. S'H20, ice = 48.0 J/(mol K), S'nz0, lig = 70.0 J/(mol K).
Glaciers are not stationary bodies of ice, but instead slowly move over time (mean speed of 1 meter/day). One reason for this is because these very large glaciers melt from the bottom, and the liquid water beneath the glacier acts as a lubricant for the glacier to move. Using the phase diagram for water (below) and concepts discussed in class, what is one potential reason that glaciers melt from the bottom at temperatures below 0°C?
What would be the equilibrium temperature if you drop 5.0 g of brass (Cp= 0.38 J/goC, initially at 68oC) and 3.5 g of aluminum (Cp = 0.9 J/goC,initially at 83oC) into 105 g of water (Cp = 4.184 J/goC,initially at 23oC)?