Calculate the resultant stress at extreme fiber in a double-J groove weld which is done to connec 12 mm thick bracket to the flange of a column as shown in the figure. 60 kN 200 mm 250 mm 12 mm thick

Q: 20 2okN KN Hinge B I the max nagative bonding momut at A

A:

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: Applied Torque= 63 N-m  Critical section is along a-a

Q: Failure Modes for Tension Members

A: Answer Tension members are subjected to three types of failures as listed below 1) Gross section…

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000…

A: To determine: normal stress in the polymer cylinder normal strain in the polymer cylinder normal…

Q: P= 78KN 100 mm 400 mm 20 mm

A:

Q: rectangular plate of dimensions gure). The plate is subjected to a c -f 12.0 MPa in the short…

A:

Q: The flange and web plates of the doubly symmetric built-up section are connected by continuous 10 mm…

A: Given data- weld size=10 mmMOI=7.73×106 mm4

Q: Q-A 16 mm thick gusset plate is connected to the 12mm thick flange plate of an I-section using…

A:

Q: A tie- down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Given data,  Diameter of the washer (Dw) = 22 mm Diameter of the bar (Db) = 6 mm Thickness of…

Q: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c)…

A: ###Determination of Normal Stress and Strain ###

Q: Problems (1) Determine the stress in each material if the left wall yields 0.6mm Bronze A=2400mm…

A: Given data in questionLoad 120 and 50 kNSpan 600 , 400 and 300 mm of bronze, aluminum and…

Q: FIGURE P1.38/39 P1.39 WP Two aluminum plates, each having a width b = 5.0 in. and a thickness t =…

A: width b = 5 inthickness t = 0.75 ina= 2 inTo find:The largest axial load P that can be applied to…

Q: Determine the maximum thickness (t) of the specimen if it is subjected to a force P = 5 KN. The bar…

A: Consider below figure ; At A ; σ = PA 100 = 5 × 100037.5 t t = 1.333 mm --------- 1

Q: In a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa…

A: Given data- direct shear stress q=50 MPabending tensile stress σb=150 MPaTo Find-The value of…

Q: 20 2okN Hinge A C Find the max nagative bonding momen nt at A due to Moving load.

A:

Q: A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What…

A: Given: The diameter of the pulley is 6 in. The diameter of the shaft is 2 in. The power transmits is…

Q: Compute the displacements of the plate t = -20 Nm uoing a single quad ekmeent a 2m I(0,1) 4 (2,1)…

A: Cross section dimension at right end b(width) = 1m d(depth) = 0.5m

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: T = 63 N. m

Q: Design a fillet welded joint to join two plates each of thickness 10 mm and 250 mm width for 100%…

A:

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel (E = 29,000…

A:

Q: A double U-shaped butt weld is to connect two plates 200 mm (d) × 20 mm (b), as shown in the given…

A: Given: A double U-shaped butt weld is connecting two plates of dimension, b=20 mmd=200 mm Moment =…

Q: A unitorm bar 1 is connected to a tapered rod 2. Both are subjected to adal loads as shown. IfP- 7…

A:

Q: A double U-shaped butt weld is to connect two plates 200 mm (d) x 20 mm (b), as shown in the given…

A: A double U-shaped butt weld is connecting two plates of dimension,Moment =

Q: Two plates are proposed to be jointed by welding as shown in the figure. Determine the size and…

A:

Q: H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of…

A: Given G1=6500ksi di = 1.25 in do=1.75 in  G2=12500 ksi Allowabe stress for tube 1 = 27ksi Allowable…

Q: Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown…

A: The diagram is shown below, Given data,                                 b=7.5''a=5.0''t=2'' The…

Q: Two triangular plates are welded together and subsequently subjected to a stress state as shown…

A: solution Given stress in x direction σx=3.5Kpa stress in y direction σy=2.5Kpa shear stress…

Q: 904. signed ed so that its cross-sectional area is reduced one-half at section E. as shown in Fig.…

A: Given Data:Cross section = 160mm2Cross section is circle=160mm dia

Q: A gusset plate is connected to the flange of column with the help of fillet weld on both sides as…

A:

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel…

A:

Q: A steel tube is rigidly attached between an aluminum rod and a bronze rod as shown. The maximum P…

A:

Q: The flange and web plates of the doubly symmetric built-up section are connected by continuous 10 mm…

A:

Q: What is the axial stress in the bronze rod (in MPa)? 2m 3m G0 KN Ismm IS mm banze rod

A:

Q: b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a…

A: Solution Given data Length of gusset plate L=140 mm Width of gusset plate b=320 mm