Answered: Calculate the radius of capillary tube… | bartleby

Related questions

Question

Calculate the radius of capillary tube if
water rise to a height 4.5 cm. Surface tension of
water is 72 dyne/cm. (angle of contact for water
= 0°, g = 980 cm/s ²).
%3D

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A capillary tube is 30 mm long and 1 mm bore. The head required to produce aflow rate of 8 mm3/s is 30 mm with acceleration due to gravity is 9.81 ms-2. The fluid density is 800 kg/m3. Calculate the dynamic viscosity using Poiseuille’s principle and kinematic viscosity of the oil.
A beaker is filled with an unknown liquid up to a depth of10.00cm. The gauge pressure at the bottom of the beaker is measured to be 1540.00PaWhat is the density of the liquid contained in the beaker? 1571.43kg/m^3 <---- ans to 1, help with following question. Does the gauge pressure at the bottom of the beaker increase more if a student adds a 15.00cm layer of oil (?oil=895 kg/m^3) or of the unknown liquid? a. The gauge pressure increases more with the addition of the unknown fluid. b. The gauge pressure increases the same with the addition of either fluid. c. The gauge pressure increases more with the addition of the oil. d. Impossible to tell.
Someone claims that the volume flow rate in a circular pipe with laminar flow can be determined by measuring the velocity at the centerline in the fully developed region, multiplying it by the cross-sectional area, and dividing the result by 2. Do you agree? Explain.
#12-21. A pipe carries water at a flow rate of 25 gpm. Determine the minimum inside diameter so that the average velocity of the fluid does not exceed: a. 10 ft/s b. 8 ft/s c. 4 ft/s.
A U-tube open at both ends is partially filled with water (Figure (a)). Oil (p = 750 kg/m³) is then poured into the right arm and forms a column L = 4.53 cm high (Figure (b)). Shield Po Water Oil (a) Determine the difference h in the heights of the two liquid surfaces. (The density of water is 1.00 x 103 kg/m3.) cm (b) The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height (Figure (c)). Determine the speed of the air being blown across the left arm. Assume the density of air is 1.29 kg/m. m/s
2. In the space below, explain what was incorrect about Ivy's reasoning. Hint: Your response will be graded on logic, clarity, accuracy, and completeness. BIU E E EE 8 fx
23. The figure shows a pipe full of water, where vi-3.00 m/s, h₁-3 m, P₁ is the gauge pressure of 5.00 x 10 Pa at the same location. Calculate the gauge pressure of the pipe's higher (3) section if A-2A and P2-3.25 x 104 Par AL h₁ Figure 14 P₁ A ha [Dm]
The piston of the hydraulic cylinder gives pin A a the instant when 0 = 54°, determiner, 7, 9, and 6.1" Answers: r = = ö = -1.2343 i -1.6988 2.7039 10.623 ft/sec constant velocity v = 2.1 ft/sec in the direction shown for an interval of its motion. For where r = OA. ft/sec² rad/sec rad/sec²
An oil tank is shaped like a right circular cylinder of diameter 4 ft. Find the total fluid force against one end when the axis is horizontal and the tank is half filled with oil of weight density 50 lb/ft³.
a Whot is the rodume ļloww rote of the auoter through the nozzle Cin m3/s)l when the diameter Îs 2-2 cmd 2 B What is the s pecd in (mi) of the water outthe house? What does the Speed of the water Coming out & the hose ne ed to be cin mis''s to reach fhe Oflower 2-6 m bed auay?
(b) What is the hydraulic diameter for flow through a semi-circular tube as shown in the figure. The diameter of the tube is 4 cm. 2.44 cm