Calculate the maximum allowable load (in KN) of a 5.0m long sawn lumber column can carry. The nominal size is 152.4 x 152.4 mm (6”x6”) and the actual size is 139.7mm x 139.7mm (5.5” x 5.5”). The applied loading is for 15-year duration and the wood used is visually graded sawn square Narra (E= 11.721 GPA, Fc = 10.342 MPa). The column is pinned both ends. Consider adjustments for load duration and moisture condition.

Calculate the maximum allowable load (in KN) of a 5.0m long sawn lumber column can carry. The nominal size is 152.4 x 152.4 mm (6”x6”) and the actual size is 139.7mm x 139.7mm (5.5” x 5.5”). The applied loading is for 15-year duration and the wood used is visually graded sawn square Narra (E= 11.721 GPA, Fc = 10.342 MPa). The column is pinned both ends. Consider adjustments for load duration and moisture condition.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the maximum allowable load (in kN) that a nominal 300mm x 300 mm sawn lumber column, 3.0m long, can carry. The applied loading is for 15-year duration and the wood used is visually graded sawn Yakal (E = 9.78 GPa, Fc = 15.8 MPa). The column is effectively held in position at both ends and is fixed for both ends.
Provide complete solution and illustration
A beam will support a combination of dead, live, and earthquake loads. The Load Duration Factor for Dead is 0.9, Live is 1.0, and Earthquake is 1.6. The Dead load causes a stress of 300 psi, the live load causes a stress of 200 psi, and the earthquake causes a stress of 100 psi. The tabulated strength of the wood is 1000 psi. What is the critical (largest) Demand/Capacity ratio for the beam? (Demand/Capacity is fb/Fb'.)
Calculate the maximum allowable load (in kN) that a nominal 350mm x 350 mm sawn lumber column, 3.5m long, can carry. The applied loading is for 15-year duration and the wood used is visually graded sawn Yakal (E = 9.78 GPa, Fc = 15.8 MPa). The column is effectively held in position at both ends and is fixed for both ends. Use k = 0.65. Blank 1
Please show your solution clearly thank you
Q1. Determine flexural strength for a wood specimen with given data below. V Span length = 22 inches , %3D Mc R = I L = span length, mm (in.) distance from neutral axis to edge of sample = ½h I = moment of inertia = bh³/12 b = average width, mm (in.) h V Cross section , b = 2" d= 2" C = where V Maximum load = 420O Ibf %3D modulus of rupture, MPa (psi) bending moment P = maximum load, N (lb) B = M = PL/4 average depth, mm (in.) || Q2. Determine shear strength for a wood specimen with given data below. Load block V a= 1.75 “ , b=0.25" , c = 2" , d= 2" V Maximum load = 510O Ibf Pmax Shear Strength || Area Test fixture Q3. Determine compressive strength for a wood specimen with given data below. V Cross section dimensions of the face on which load is applied = 2" x 2" V Maximum load = 4500 Ibf Load Pmax т Compressive Strength Area a * b
What is the size factor for bending of 4x10 dimension lumber?CF=_______
A third-point bending test was performed on a 100 * 150 mm wood lumber according to ASTM D198 procedure with a span of 1.8 m and the 150 mm side is positioned vertically. A strain gauge is glued at the center point between the supports. The strain gauge is zeroed at the start of the test when the force is zero. A strain of 0.00456 is measured when the combined load is 6.672 kN and the load–strain curve is in the linear range. Determine the flexural modulus of elasticity. If the maximum combined load on both loading bearings was 22.722 kN, calculate the modulus of rupture.
The wood has an allowable normal stress of Oallow = 15 MPa and an allowable shear stress of Tallow = 1.33 MPa. (Figure 1) Part A Determine the minimum dimension h of the beam's cross section to safely support the load. Express your answer to three significant figures and include the appropriate units. µA ? h = Value Units Submit Request Answer Figure Provide Feedback 25 kN/m B 2 m 100 mm
Compute for the Modulus of Elasticity of the Wood if the Clear Span Length is 2300 mm, applied load is 10lbs and the deflection of the wood is about 16.5mm. Moment of Inertia of the wood is 2.75x105 mm4 o 2.59 GPa o 2.49 GPa o 2.74 GPa o 2.63 GPa
SIZED-BOND PAPER. 1. A center-point bending test was performed on a 2 in x 4 in wood lumber according to ASTM D198 procedure with a span of 4 ft. and the 4 in side is positioned vertically. If the maximum load was 240 kips and the corresponding deflection at the mid-span was 2 in, calculate the modulus of rupture and the apparent modulus of elasticity
A static third-point bending test was performed on a 100mm x 100mm x 5000mm wood sample according to ASTM D143 procedure. (span between supports = 4800mm). If the maximum load was 2,900N, calculate the modulus of rupture of the wood.