Calculate the force on Member CH in Kips by the method of sections. if the given 30kip load at joint J and 25kip loads at joints B, C, D, E from the figure are replaced by 85kip and 108kip loads respectively. Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.

Q: Analyze the howe truss with the given dead load as shown in the figure. Bottom chord dead load = 5kN…

A: Solution: Dead load = 5kN Because of the symmetric truss and load: A=Hy=12total load = 0.5 × 5 × 5…

Q: C. Steel bar whose length of 1 + 0.DD m and a radius of 10+MM mm. is subjected to torque which…

A:

Q: E K C d D F d A I d H Use your assigned n value. Given: • d = 5 meters • P= 5n 1. Using the method…

A:

Q: 3 m B 95KN 95KN 4 at 3 m = 12 m

A:

Q: THE RIGID BARS SHOWN ARE SEPARATED BY A ROUER AT C AND PINNED AT A X D. A STEEL ROD AT B HELPS…

A: Given data:

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A:

Q: Determine the maximum tensile and compressive bending stresses developed in the beam shown. The…

A:

Q: Determine the force in members GF, FB, and BC of the Fink truss and state if the members are in…

A: A truss hinged at A and roller supported at D. Vertical forces 800 lb, 600 lb, and 800 lb act on G,…

Q: The signboard truss is designed to support a horizontal wind load of 610 lb. If the resultant of…

A:

Q: A cast-iron beam has a section as shown in the figure below. The beam is subjected to Q2…

A: ASKED: To determine the width of the flange of the beam.   Given, Width of flange (X) = ? mm…

Q: A В C D a E F G Н F

A: using method of sections sign convention tensile =+ compressive = -

Q: Knowing that a factor of safety of 3.01 teel structure shown. Member AB ha Use Yield Stress a, 250…

A:

Q: Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN,…

A: given- FBD-

Q: A short length of a rolled-steel column supports a rigid plate on which two loads P and Q are…

A: Force = P + QMoment, M = 6 Q - 6 PA = 10 in2x = 5 inIz = 273 in4

Q: 1. The section shown in the figure fails in flexure. Determine the magnitude of the compressive…

A: Given Data: a = 8 in, b = 16 in, h = 28 in Dia of hole = 8 in f`c = 5 ksi and fy = 60 ksi To find :…

Q: tension. Consider the truss shown in (Figure 1). Set P = 7 kN, P2 = 9 kN, P, = 13 kN μΑ FBE = Value…

A:

Q: Use Virtual Work Method to answer the questions below considering the truss shown in the figure.…

A:

Q: Given the truss and loading shown below, determine the stress at member AB if Pu = 18.375 Kips and…

A: Given:- Pu=18.375 kipsArea of member  AB isA=23 in2 To find:- Stress in member AB

Q: At a particular section of a beam with the given cross-section, an internal shear force V and…

A:

Q: . Assume that axial eformation of Member EF is aused mainly by its reaction external forces on the…

A:

Q: dAB =? dec 40 тm 0 (+) A B C T 1200 тm 800 тm

A:

Q: a) Determine the force in member BG of the truss.  b) Determine the force in member CD of the…

A:

Q: 1. Assume that axial deformation of Member DF is caused mainly by its reaction to external forces on…

A:

Q: The principal stresses are incorrect but the maximum shear stress is correct.  What are the two…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in…

A:

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas.…

A: Take moment at A to be zero

Q: gid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that…

A: To find value if load P

Q: Consider the truss shown in (Figure 1). Suppose that F1 = 40 kN and F2 = 30 kN . Part A Determine…

A: Given: The force F1 is 40 kN. The force F2 is 30 kN. Consider the figure,

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 50…

A:

Q: Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40…

A: Given Data:Tensile stressft=40MpaCompressive stress fc= 80MpaINA= 20×106mm4

Q: The bar AB is being supported by bars at each end. The length and the area for each bar are given.…

A: Given: The load on the bar AB is 100 N. Consider the figure,

Q: Consider the truss shown in (Figure 1). Take A = 0.0015 m? and E = 200 GPa for each member, and F =…

A:

Q: Consider the truss shown in (Figure 1). Suppose that Fi = 55 kN and F = 30 kN Part A Determine the…

A: As per our guidelines we are supposed to do  only 1 question. Kindly post other question separately

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A:

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.