Calculate the following efficiencies for an assumed pumping system: a. Electric drive motor efficiency. b. Pump efficiency. c. System overall efficiency. Use the following inputs and outputs: Motor input power -3.73 kW: motor output power = 3.36 kW. Pump input power = 3.36 kW: pump output flow= 26 L/min: pump output pressure = 6895 kPa.

Calculate the following efficiencies for an assumed pumping system: a. Electric drive motor efficiency. b. Pump efficiency. c. System overall efficiency. Use the following inputs and outputs: Motor input power -3.73 kW: motor output power = 3.36 kW. Pump input power = 3.36 kW: pump output flow= 26 L/min: pump output pressure = 6895 kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P
You and a friend plan to throw one end of a hose over a tall fence to siphon water from your side to the other side. Your friend says it doesn't matter how high the fence is, it will always work as long as your end of the hose is higher than the other side. However, you remind him that isn't actually true. What is the potential problem and about how high can the fence be (in meters) before it becomes an issue?
Question 2 A hydro-electric power station has a reservoir area of 3,8-km2 and a capacity of 9,9 x 106 m3 . The effective head of water is 100 metres. The penstock, turbine and generation efficiencies are 95%, 90%, and 85%, respectively. 2.1 Determine the overall efficiency of the power station (%) and determine the total electrical energy that can be generated from the power station (kWh). 2.2 Determine the depth of the reservoir (metres) 2.3Determine the fall in reservoir volume level is the load of 100 kW is supplied for 5 hours (%).
Q2. Design and plot a hydraulic system for drive and control aircraft flap to overcome 500 N aerodynamic forces with the following specifications:- The actuator single acting cylinder with bore diameter 25 cm , smooth pipes line has diameter and total length 15 mm and 12 m respectively, six elbows (K = 0.9), if average velocity of the oil in the pipes 20 m/s and total pressure losses across control valves and other accessories 1.4 bar. Determine total pressure pump required for hydraulic circuit. (Note:- poil =880 kg/m², voil= 64.2 mm/s)
c) Water is pumped from a deep well (located 20 m underground) to a hilltop reservoir (located at 50 m above ground level). Water is being transferred at a rate of 4800 LPM while the pump consumes 60,000 kW of electric power in the process. Assume that there are no frictional losses in the piping system and the change in kinetic energy between the inlet and outlet of the piping system is negligible. Determine the overall efficiency of the pump-motor setup.
1) A plot of pump net head is shown below. Two curves are drawn: blue color curve and red color curve. Which one is called pump performance curve? Will the location of pump performance curve change if the velocity of the fluid at pump outlet changes? a) red curve; No, the location will not change b) blue curve; yes, the location will change c) red curve; yes, the location will change d) blue curve; No, the location will not change 2) In a turbine system, states A and B are homologous. If the net head ratio HA/HB =16 , volume flow rate ratio VA˙/VB˙=9. What is the diameter ratio DA/DB ? a) 3/2 b) 6 c) 12 d) 2/3
A 5 kW electric motor driving a pump has an efficiency of 85%. Determine the losses encountered in the driver. a. 2500 kJ/hr b. 48.00 kJ/min c. 0.78 kW d. 2700 kJ/hr
5. The average wind velocity in a particular area is found to be 5.5m/s. It is proposed to install a wind driven turbine with a blade radius of 1.8 m. The proposed design has an interference factor of 0.21 and an axial force coefficient of 0.89, and a torque coeffi- cient of 0.8. Determine: a) The expected power output of the turbine. b) Thrust on the turbine. c) Torque on the turbine. d) Rotational speed.
pump is open to The figure below shows a liquid-level system in which two tanks have cross-sectional areas, A₁ and A2, respec- tively. A pump is connected to tank 1 through a valve of linear resistance R₁. The inlet to the atmosphere, and the pressure of the fluid increases by Ap when crossing the pump. The liquid flows from tank 1 to tank 2 through a valve of linear resistance R₂ and leaves tank 2 through a valve of linear resistance R3, exiting at at- mospheric pressure. Assume the density p of the liquid is constant and note that both tanks are open to atmosphere as shown. Pa Ap Your Tasks: R₁ Pa ÍRN A₁ R₂ Ple Pa A₂ R3 → 9 A. Derive a differential equation model for the system behavior in terms of the liquid heights h₁ and h₂. B. Put the differential equations into second-order matrix form.
Q1: The pump shown in Fig. P8.75 delivers a head of (hp) 250 m to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 200 m.
Q.4.B. Water flow from a lower reservoir to a turbine, where electric power is generated. The overall efficiency of the turbine-generator is 84%. Determine the electric power output of this plant. (Pwater = 1000 kg/m²) 54 m/s Tubine Generator
The steam turbine shown below has a single inlet and two exit streams. It is assumed that the turbine is well insulated and the change in potential energy is negligible. The energy equation governing the turbine based on these assumptions is: OA) B) OD) inlet Turbine J QT - WT=0 C.V. Qr − W₁=m₂ (h + F7)2 +m3 (h+VZ)3-m₂ (h+ QT - Wr=m₂h₂+ m3h3- M₁h₁ w C.V. W₁=m₂ (h+)₁-m₂ (h+)₂ - m₂ (h+)₂