Calculate the following: 1. Mesh Equations 2. Voltage at point AB; 3. Apparent Power at points AB; 1 jwC₂ =4 R₁=1 R₂ jwM=j5 j2 = jwL1 I₁ h₂ 10= V(+ -3j= 1 jwC1 A jwL2 =j7 13 ww R3=9 B =-j8 R4=

Q: 1. Normal benchtop digital multimeters (DMMs), such as pictured below, can only measure resistances…

A: Electrical resistance is measured with an ohmmeter, a device that uses that unit of measurement. The…

Q: ! Required information Consider vs(t) = 9.00 - 2u( V for the circuit given and the 15- resistor is…

A: Given:a circuit,with, we need to determine:, the voltage across capacitance at 4 ms.

Q: Can tutor write the explanation more clearly as I don't understand the hand writting

A: A flip flop change it's output at active edge of clock.  Preset is used to set the output of flip…

Q: What is sourcing current, and its connection to switching of power? It's confusing. Please help.

A: Power: It is amount of energy which transferred per unit time, it means rate of doing work. It is a…

Q: Hi,  Are you able to go into some more detail on its opperation if possible.

A: Given: To explain: The operation of the circuit as a NOT gate.

Q: What is the required resolution of an instrument if the product characteristic specification is 10.0…

A: The number of bits or portions that the output or displayed reading from a sensor or measuring…

Q: MUI ULTIPLE SELECTIO With respect to the following figures, which of the following statement(s)…

A: Given Data:A E vs k curve is given in the question.Required Data:Here, we need to mark the correct…

Q: 120 V Computer (500 W) Lights (500 W) Fridge (500 W) Fuse T.V. (500 W) 20 A A) What is the current…

A: Nodal Analysis - It is used to find node voltage using Kirchhoff's current law. Kirchhoff's current…

Q: 4) Determine the shown below gain and bandwidth for the circuit. RF $330k Rs = 10K 22 15MH₂ f

A: We need to find out the gain and bandwidth for given opamp .

Q: Determine the take-up and measurement to your mark for each of the following. Length EMT Size…

A: According to the question, we need to calculate take-up and mark for the given EMT size.

Q: Silicon is doped with 3 x 1018 arsenic atoms/cm³ and 8 x 1018 boron atoms/cm³. (a) Is this n- or…

A: We need to tell about type of semiconductor and hole and electron concentration for given…

Q: What is a matching circuit?

A: Matching circuit : A matching circuit is a circuit which is mainly connected by source and load at…

Q: Don't use ai to answer I will report your answer Solve the question with correct answer and proper…

A: Relationship ExplanationBreakdown Voltage: This is primarily determined by the doping levels and the…

Q: 15 Ω 24 N ia 10 Ω ww 19N 12 V 25 N ia 10 V ic O (10)(i. – ia) – (12)(ic – is) + (25)(ic – ia) = 0 O…

A: We need to write krichoff's voltage equation for given loops .

Q: Match the image with the correct digital-multimeter setting. Your setting choices are "resistance",…

A: The multimeter is a device used to measure the various parameters in an electrical circuit like…

Q: CELLLI Symbolab Sed https://ms.tu.edu.sa/bbcswebdavip. Six - Write short notes about Sockets Types &…

A: As per our policy, i have attempted only 1 part. Socket types - Stream sockets allow communication…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.