Calculate the flow stress at the end of the stroke of this material at the given temperature assuming coefficient =0.2 ↓Fill the blanks of the following table:HeightDiameterhavgDavgReduction inheight %Force(measured)Before deformation (mm)20.76 20.80 20.7915.46 15.81 15.1224.70 24.55 24.45 29.18 29.72 29.7920.7824.5715.46-20.78|20.7839KN=25.60After deformation(mm)15.4629.56

Given DataF=39kNh2=15.46 mmD2=29.56mmμ=0.2

Answered: Calculate the flow stress at the end of…

Engineering

Mechanical Engineering

Calculate the flow stress at the end of the stroke of this material at the given temperature assuming coefficient =0.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated.…

A: NOTCH SENSITIVITY FACTOR(q) It is defined as the susceptibility of a material to succumb to the…

Q: 4. Solve problem 8.10 in our textbook (find the safety factor for failure at the fillet). Note that…

Q: How can we find the maximum normal and maximum shear stress at the point?

A: Normal Stress: Normal stress is the amount of stress that occurred in a member when it is loaded by…

Q: Assume A is pinned and B is a roller in (Eigure 1). Take that w = 9.0 kN/m. Determine the normal…

Q: In a cruise ship, a liferaft is hanged by suspending it with a thick metallic cable attached to both…

A: Given, Tension in the cable , T = 40 KN Maximum allowable shear stress = 50 * 106 Pa

Q: Problem 1. A standard square spline joint with dimensions z x dx D= 8 x 32 mm x 38 mm and lengthl =…

Q: Q.4 Calculate the elastic constant G and K of a cylindrical bar of diameter 30 mm and of length L m…

Q: A circular dis of lead of radius 150 mm and thickness 50 mm is reduced to a thickness of 25 mm by…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: The principal stresses are given as 20, 0 and 30 respectively, what is the shear stress? Selected…

A: To find: The shear stress. Given: The principle stress is σ1=20, σ2=0 and σ3=30. Concept used: The…

Q: A o 25 mm hole is pierced in a t = 2.5 mm thick steel sheet having shear strength t = 350 MPa. If…

Q: During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow…

Q: Given data : Maximum principal stress=100 Mpa Minimum principal stress=-50 MPa Determine maximum…

Q: How do you calculate the principle stresses for Mohrs Circle?

A: Mohr's circle is used to represent a plane state of stress or a two-dimensional state of stress.…

Q: A tensile specimen of the metal of 100 mm is length stretched to a length = of 157 mm during the…

Q: 1) The curve of stress versus time on the cross section of engine connecting rod is shown in the…

A: Given data: Maximum stress, σmax = 78.61 N/mm2. Minimum stress, σmin = -10.75 N/mm2. Calculate the…

Q: 8. What temperature will the rails just touched if steel railroad is 10 m long are laid with…

A: Dear student, According to the guidelines I am allowed to answer only one problem…

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: 2) Steam of 3.5MPA is transported in a pipe of outside diameter 450mm. (Pressure 3.5MPA) The walls…

A: Given data Steam pressure = 3.5 MPa OD of pipe (D) = 450 mm thickness of pipe (t) = 10mm bolt dia…

Q: A rectangular post which is made up of two blocks of wood glued together along a joint inclined at…

Q: What is the yield strength in shear of a rod with a maximum allowable shear stress of 140 MPa if a…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

Q: 1) A set of pipes are available with 50-mm inner-diameter and varying outer-diameters from 51 mm to…

A: Given that, Inner diameter of pipe, Di=50 mm,Outer diameter=DoPower available from shaft, P=110…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: 8 mm x 36 mm Calculate the shear

A: for solution refer below images.

Q: I need it handwritten and both derivation or else skip Derive the equations which related to the…

A: (A) Maximum principal stress theory:-The theory states that the failure of the mechanical component…

Q: THICK-WALLED PRESSURE VESSELS A steel compound cylinder is formed by shrinking a tube 400 mm outside…

A: To calculate the maximum shear stress values at different locations on the compound cylinder wall,…

Q: 40 mm 10 mm 40 mm n aluminum tube with the cross section shown has a constant wall thickness mm. A…

A: GivenT=400N.mG=8Gpa

Q: Find normal stresses and shear stress at the given inclination ..using mohr circle

Q: Problem 6-4 A compound cylinder is made by shrinkage an outer tube on to an inner tube, the final…

A: We know that a compound cylinder is created by shrinking an outer tube onto an inner tube, with…

Q: Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the…

A: Another name of rivet joint is lozenge joint. Selection of material σt=80 mpaζ=65 mpaσc=160 mpa

Q: At a larger radius the rate of shear strain is 18 s-1 and the consistency coefficient is 0.6 Pa s.…

A: Given:Rate of shear strain, γ=18 s-1Consistency coefficient, k=0.6 Pa.sFind:The shear stress.

Q: Given Ox = -7Mpa, Oy = 3 Mpa y T = 8 Mpa, calculate the greatest principal stress and the maximum…

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

Q: In an experimental determination of principal stresses a cantilever of hollow circular cross section…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

Calculate the flow stress at the end of the stroke of this material at the given temperature assuming coefficient =0.2

↓
Fill the blanks of the following table:
Height
Diameter
havg
Davg
Reduction in
height %
Force
(measured)
Before deformation (mm)
20.76 20.80 20.79
15.46 15.81 15.12
24.70 24.55 24.45 29.18 29.72 29.79
20.78
24.57
15.46-20.78|
20.78
39KN
=25.60
After deformation(mm)
15.46
29.56

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

0/ During the rolling process, the average flow stress is 20,000 lb/in², etermining the amount of reduction in the cross-sectional area (use n = 0.40 and K = 35,000 lb/in²).
12. An aluminum sleeve is held between the head and the nut of a steel bolt. The temperature is raised 40°F from 60°F after the nut is turned 45° against the sleeve from loose contact therewith. Calculate the stresses in the sleeve and the bolt. BOLT IS 1/2" DIA, 16 THREADS/ IN. E(ALUM.) 10 x 106 psi E (STEEL)= 30×106 psi Coefficient of linear expansion STEEL: 6.5 x 10-6 °/°F ALUM: 12 x 10-6/F
The tube has a length of 2 m and is made of the material with the properties provided in the following figure. (a) Determine the torque needed to just cause the maximum strain to reach 0.015. (b) What is the permanent angle of twist of the tube when this torque is removed?
An aluminium slab of 750 mm x 80 mm x 36 mm is forged to the thickness of 25 mm. Find the upsetting force if the flow curve of aluminium is o=1400.25 MPa and the coefficient of friction is assumed to be 0.2. 750 mm 750 mm 36 mm 25 mm 2a 80 mm
10.5 (B) A compound tube of 300 mm external and 100 mm internal diameter is formed by shrinking one cylinder on to another, the common diameter being 200 mm. If the maximum hoop tensile stress induced in the outer cylinder is 90 MN/m² find the hoop stresses at the inner and outer diameters of both cylinders and show by means of a sketch how these stresses vary with the radius. [90, 55.35,-924, 57.8 MN/m²]
Graphically present the general form of the maximum shear stress variation across the compound cylinder wall clearly indicating the values at the cylinder bore, common interface and the outer surface. What do you infer by comparing the shear stress distributions in the respective cylinders?
MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.
Write answer
Define Transverse Shear Stress Word Description: Sketch or Drawing: Equation: Units:
Thank you for helping me