Calculate the flow in an earth-lined (n = 0.022) trapezoidal canal having bottom width of 5.5m, side slope 1H:2V, laid on a slope of 0.00014 having a depth of 2.4m, using Manning's c.

Q: You are the engineer supervising the layout of a piping system. In a certain portion of the pipe,…

A: Given, L = 10 m  D = 30 cm or 0.3 m V = 15 m/s  k = 0.003456 ∆L = 0.02 mm or 0.00002 m  ∆V = 0.1…

Q: Write a note on Turgo Turbine also write functions of its main components?

A: Turgo turbine is an impulsive water turbine and handles flow rates more than the flow rates of…

Q: If atmospheric pressure is 13.99 psi, and a gage attached to a tank reads 7.9 in Hg vacuum, find the…

A: Given: Atmospheric pressure = 13.99 psi Gage reading = 7.9 in Hg vacuum   Also, Specific gravity of…

Q: Duration in Weeks Activity 1- 2 8 1-3 5 1- 4 6 2 - 6 7 3 - 4 3 - 6 10 4 - 5 4 - 7 7 5 - 7 6 - 7 6 -…

A: Early start and last start has been shown in the chart diagram. Critical path is a longest way to…

Q: Write a detailed note on Pumps and Turbines with emphasis on the following for both . a) Types b)…

A:

Q: List some common industrial uses of venturi suction cups.

A: Venturi suction cups supplied by air have traditionally become a viable alternative for quick,…

Q: Instruction: Evaluate and find all the requirements with proper, neat, and readable handwriting…

A:

Q: i) A system for an ordinary toilet tank filling is shown in figure below. The ball floats on the…

A: The block diagram for the system as below,

Q: Discussion: 1. What are the different between variable types of flow control valves? 2. What are the…

A: Solution: 1. Flow control Valves are basically used to regulate the pressure and rate of Flow in the…

Q: Why is a two-pipe vacuum steam-heating system used in large buildings?

A: For the application of ventilation, air conditioning to carry the steam and to return condensation…

Q: Urgent Hello please answer this problem as soon as possible. Topic is 'Fluid flow measurement' in…

A: Given data- Diameter of orifice d1 =75 mm = 0.075 mOrifice discharge Q = 23.41…

Q: A hot water baseboard radiator has 12 fins per inch. How many fins are in 72inches of the radiator?

A: The number of fins per inch is 12. The total inches are 72. The total fins are obtained by…

Q: According to DOLE-OSH standards, during entering the confined space, no smoking or open lights,…

A: 1. Confined Space refers to a place of enclosed nature that creates conditions that give rise to a…

Q: Which system makes use of a gravity tank to a deliver water to different fixtures in a building? a.…

A: There are different methods used to distribute the water from a tank to the different fixtures in…

Q: As an engineer, conduct a research on the hot and cold water supply system of a building,…

A: Here it is asked to conduct a research on hot and cold water supply system of building, institution,…

Q: Name the equipment that uses the principle of absorption for the removal of gaseous pollutant.

A: Scrubbers are one of the primary device that control gaseous emissions, especially severely…

Q: Give the discharge/flow rate in (m3/s) of the system with a constant velocity of 2.5 m/s given the…

A: given - velocity,V and diameter,D to find - discharge, Q

Q: Determine the horizontal and vertical components of reaction at point C*

A:

Q: Water flows through a 75 mm diameter pipe at a velocity of 3m/sec. Find (a) the volume flow rate in…

A:

Q: Conservation of energy in a hydraulic system is described E O Hazen-William's Equation Manning's…

A: Conservation of energy in a hydraulic system is described by Bernoulli's Equation. The correct…

Q: hoose the letter of the correct answer. Pipe fittings are attached to the end of pipes to allow it…

A: The part which is attached to pipe is known as pipe fitting.

Q: What is the percent passing on pan? (2 decimal places, no need for unit)

A: Given the data of sieve analysis as,  Sieve Size Weight of retained fine aggregates (g) Trial 1…

Q: Consider the three pipes shown below in cross section. From left to right, they contain water,…

A: Give data,in three pipe cross section contains water, mercury and gasoline respectively.all pipe…

Q: EXAMPLE: Waterworks of a town treat 35 x 106 litres/day. The water is treated by…

A: Given data - Q = 35×106 L/day Consumed filter alum = 20 mg/L Alkalinity of water = 4.5 mg/L of CaCo3…

Q: 11. The path taken by the smoke coming out of a chimney (in concentric circles) represents a a)…

A:

Q: Using illustrations, explain the practical use of creating a hump or a sudden drop in the bed of a…

A: We are considering a situation in which flow has already been established after the creation of…

Q: 1) A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi…

A:

Q: 14. The observation deck of tall skyscraper 370 m above the street. Determine the time required for…

A:

Q: Describe the working principle of screw compressor with figure.

A: Screw compressor It is a type of rotary compressor which help s in compressing air due to screw…

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A:

Q: 1. Explain the step by step method of designing a high gravity dam. (Hydraulic Structure)

A:

Q: For the flow indicated in the shown figure, which section is representing the Vena contracta? a…

A: Vena contracta is the location of the stream where cross section of stream is minimum and the…

Q: * View B Quizzes - ENGINEER 1EE0:Introdu x B Homepage - CIVENG 2004:Fluid x O assignment_4 (1).pdf…

A: Given data: Diameter of the tank = 1 m Diameter of the hole = 8 cm Initially water level in the tank…

Q: (c) The figure below shows a Venturi meter used to indicate the speed of flow of a liquid through a…

A: Concept: Given problem can be solved using concept of Bernoulli’s equations. When liquid passes of…

Energy Sources

An energy source refers to the various sources, whether natural or artificial, which are primarily used for the generation of electricity by power plants. Production of electricity by power plants demands the consumption of energy sources in large quantities, which cannot be fulfilled by traditional sources, such as coal and wood. Also, the mere usage of such sources leads to their depletion at a much faster rate.