Calculate the factored load capacity of a double channel section member of A36 steel according to AISC LRFD Specification. The member is 4m long and consists of 2Cs 180x19.5, with flanges turned out with clear gap of 90mm. Assume that there can be as many as two 14mm rivets at any one cross-section (one in each flange). U = 0.80.

Calculate the factored load capacity of a double channel section member of A36 steel according to AISC LRFD Specification. The member is 4m long and consists of 2Cs 180x19.5, with flanges turned out with clear gap of 90mm. Assume that there can be as many as two 14mm rivets at any one cross-section (one in each flange). U = 0.80.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.15P

See similar textbooks

Similar questions

أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by ¾ inch boltas shown below. Use A36 steel with Fy=36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa. A-36 steel is used. The applied force "T" is equally divided among the bolts. Assume bolt hole diameter to be 3 mm bigger than bolt diameter. Diameter of bolt is 20 mm. T/2 T T/2 10 mr 10 mm T/2 300 mm T/2 Determine the capacity of the connection if shearing governs in kN. A 1548.58 B 1170.56 1290.62 D 1439.25 000
2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel. PL 5x200mm PL 5x200mm Pu PL 10x200mm Pu
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
PSD323- Principles of Steel Design 4. The tee section is made up of a 30mmx150mm flange and a 30mmx160mm web. Determine the properties of a section(MOI, section modulus, radius of gyration) 15d mm 30 mm A, 6 Yu d, N.A. di 30 tnm 160 mm
please use SI for unit
?
A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, F,= 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.-- b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-- 210 mm -Tension Plate M20 bolts
SOLVE FOR1 HR