Calculate the exit diameter, if at the inlet section of the draft tube the diameter is 1 mand the pressure is 0.405 bar absolute. The flow rate of water is 1600 L/s. The verticaldistance between inlet and outlet is 6 m. Neglect losses.

Given: The diameter of the inlet draft tube is 1m. Pressure at the inlet is 0.405 bar absolute.…

Answered: Calculate the exit diameter, if at the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

M4
i need the answer quickly
A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of 1750 r/min.Neglect losses. If r 1 =6 in, r 2 = 14 in, b 1 = b 2 =1.75 in,V t 1 = 10 ft/s, and V t 2 = 110 ft/s, compute the absolutevelocities ( a ) V 1 and ( b ) V 2 and ( c ) the horsepower required.( d ) Compare with the ideal horsepower required.
Q3.A Francis turbine has the dimensions of r=1.42 m, r,=2.00 m br=2.20 m and by=0.731m. Rotation speed of the turbine is 180 rpm. Three angles of velocities at the inlet and outled of the blade are defined as oaz= 35° and al=25° The flow rate of turbine is 340 m/s and the total head of the turbine is 80 m. Neglecting losses, www a) Draw the velocity three anges at inlet and outlet of the blade. b) Calculate blade angles at inlet and outlet of the blade, Power. Net head of turbine. c) Losses in water channel (Penstock). Note: Point (2) presents inlet and while point (1) presents outlet section of blade. Adjustable guide vane Blade n
Problem 01 Water from a large reservoir is discharge to atmosphere through a 100 mm diameter pipe and 450 m long. The entry from the reservoir to the pipe is sharp and the outlet is 12m below the surface level in the reservoir. Taking f=0.01 in the Darcy formula, calculate the discharge. Problem 02 Water is discharged from a reservoir into the atmosphere through a pipe 39m long. There is a sharp entrance to the pipe and diameter is 50 mm for 15 m long from the entrance. The pipe then enlarge suddenly to 75 mm in diameter for the remainder of its length. Taking into account the loss of head at entry and at the enlargement, calculate the difference of level between the surface of the reservoir and the pipe exit, which will maintain a flow of 2.8 dm³/sec. Take f as 0.0048 for the 50 mm pipe and 0.0058 for the 75 mm pipe. Problem 03 V d Water is pumped with a velocity 2, 8 m/s in a 150 mm diameter pipe. The H₂ branches at A into a 75 mm diameter pipe, 50 m long with f-0,008, and a the 100…
A plugged dishwasher sink with the dimensions of 16 in. ✕ 19 in. ✕ 5 in. is being filled with water from a faucet with an inner diameter of 1 in. It takes 250 seconds to fill the sink to its rim. Imagine the plug of the sink leaks. If it now takes 290 seconds to fill the sink to its rim, estimate the mass-flow rate of the leak (in lbm/s).
A pipe of 180mm bore is delivering water at a rate of 8250dm3/min at a pressure 800kN/m2. It connects by a gradually expanding pipe to a main of 300mm bore which runs 3,5m above it. Find the pressure in the 300mm main, neglecting all losses.
quick answer pls
The sprinkler system is used for watering the garden as given figure below. Working fluid enters the system at 2,02 liters/s. Calculate the required torque (N.m] holding the system as stationary for e-30°. (NOTE: Take p-1000 ka/m) Nozzle exit area normal to relative velocity = 18 mm =0.5m Yanıt:
The suction water level of a reservoir is 5 m above pump centerline and the discharge water level is 50 m above pump centerline. The discharge is 0.2 m^3/s with suction pipe of 100 mm diameter and 90 mm diameter discharge pipe. The total head loss is 50% of the velocity head at suction pipe. If pump runs at 360 rpm, find the torque (in kN-m) developed by the shaft of the motor if pump efficiency is 76%.
The discharge velocity is 49 m/sec and 456 mm water gage. The suction pressure is 81 mm water vacuum and velocity of 4 m/s. Calculate the fan total head in terms of water
10.The nozzle shown in the figure creates a horizontal jet of alcohol ( s = 0.79 ) which strikes a vertical plate. If the jet causes a force of ( 500 N ) on the plate, calculate : a) The mass flow rate of alcohol. b) The pressure at section ( 1) if there is no losses in the nozzle. F D=5 cm D;=2 cm Univer Mechar Univers of pert

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Calculate the exit diameter, if at the inlet section of the draft tube the diameter is 1 m and the pressure is 0.405 bar absolute. The flow rate of water is 1600 L/s. The vertical distance between inlet and outlet is 6 m. Neglect losses.