Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cdCarnot cycleTHLTc2016 Pearson Eduction, Inprocesses; and the volumes involved are Va, Vb, Vc, Vd, and the two temperatures TC andprocesses and segment ab & cd are theWhere segments ad & bc are theSol.Since AU = 0, then the heat on segment ab isQH =TH In |The heat on segment cd isQC= .TC InBy inspection, we can say thatvr-1andTHV-1Thus,Vb/then|Qc/QH| = |Which solves the efficiency of the Carnot engine.

Answered: Image /qna-images/answer/76e94947-94df-4c3d-850a-4059bca566a5.jpg

Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd Carnot cycle Он TH 2016 Parson Education, inc Where segments ad & bc are the processes and segment ab & cd are the processes; and the volumes involved are Va, Vb, Vc, Vd, and the two temperatures TC and Sol. Since AU = 0, then the heat on segment ab is QH = TH In | The heat on segment cd is QC = . TC In | By inspection, we can say that and TH VY-1 Thus, Vb/ then 1Qc/QH| = | Which solves the efficiency of the Carnot engine.

Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd Carnot cycle Он TH 2016 Parson Education, inc Where segments ad & bc are the processes and segment ab & cd are the processes; and the volumes involved are Va, Vb, Vc, Vd, and the two temperatures TC and Sol. Since AU = 0, then the heat on segment ab is QH = TH In | The heat on segment cd is QC = . TC In | By inspection, we can say that and TH VY-1 Thus, Vb/ then 1Qc/QH| = | Which solves the efficiency of the Carnot engine.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Solve it fast fast plz
An open-circuit voltage of 480 V appears across the slip-rings of a wound-rotor induction motor when the rotor is locked. The stator has 8 poles and is excited by 60 Hz source. If the rotor is driven by a variable-speed dc motor, calculate the open-circuit voltage and frequency across the slip rings if the dc motor turns a. At 500 r/min, in the same direction as the rotating field b. At 600 r/min, in the same direction as the rotating field c. At 1800 r/min, opposite to the rotating field
.
A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power S that this motor is using b) In order to get lower electrcity bill it is desired to connecta parallel compensator to the motor so as to get pf-0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power S S+ S, that will achieve the desired pf, where Sc is the power of the compensator ) Determine the complex power S. of the compensator and the value of the parallel compensator impedance. What type of circuit element should be the compensator?
A dc separate excited generator operate at speed = 1500 R.P.M at a certain excitation gives a voltage = 180 Volt. Its voltage at speed 110 rad/sec and half excitation is: 065.23 V. 070.15 V. 063.02 V. O None.
Q#3: Practically we observed that in single phase induction motor a capacitor is need for starting purpose. The question is that why we need the capacitor? And if the capacitor is not available then which device or element will use to start the single phase induction motor? Solution#3 (to be typed here by the student)
In the Chapman-Enksog predictive model of conductivity of gases, increasing the temperature from 300 K to 400 K will increase the conductivity by the 2k to be independent of temperature. Why? A) 15.4 B) 33.3 C) 86.6 %. Assume that
Q2. A de shunt generator has a full load curent of 50A at 200V. The stray losses are 500w and Ra 502. If the full load efficiency is 80%, find ) Ra (ii) Load current corresponding to maximum efficiency (i) Draw the variation of load current with efficiency (estimate)
find 1-transfer function of Dc Separately Excited motors (step by step). 2-Block diagram of Dc Separately Excited motors Ra La www mm Ia Va !Luw! GEH mm Tm, J, B,0