Calculate the drawdown in a drainage well having a radius of (50cm), with a lowering in water table at point P1 at a distance of (100m) from the well of (1m) lowering, and a lowering of (4m) at point P2 with a distance of (40m)from the well. Saturated thickness is (40m) while pumping is 2000 m³/d.

Calculate the drawdown in a drainage well having a radius of (50cm), with a lowering in water table at point P1 at a distance of (100m) from the well of (1m) lowering, and a lowering of (4m) at point P2 with a distance of (40m)from the well. Saturated thickness is (40m) while pumping is 2000 m³/d.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q₂: A) At the beginning of a given day a reservoir has a surface area 30 Km. The inflow to the…

A: Reservoir surface area (A) = 30 km2 Inflow rate (Qi) = 80 m3/s Outflow rate (Qo) = 15 m3/s Seepage…

Q: struction, the piezometric surface of the aqu mate the subsidence caused by the project. 9.13.…

Q: Consider that the flow rate of 0.020 cumecs is being conveyed from Reservoir A to Reservoir B.…

Q: A well of 0.5 m diameter is pumped from confined aquifer at 0.08 m'/s. The draw- down recorded at…

A: Thiems equation and dupits equation is generally used for confined and unconfined aquifier analysis.

Q: Group work Example Two reservoirs with a difference in water levels of 180 m and are connected by a…

A: Head = H = 180m Length = L = 64Km or 64000m Diameter of pipe = D = .6m Friction factor = f = .015

Q: A water treatment plant has a capacity of 110,000 m³/day with two horizontal flow settling basins,…

A: Given Discharge 110000 m3/dayLong 24.5 mWidth 18 mDeep 3.7 mAngle 60°To find out Surface loading…

Q: Water Supply from an Unconfined Aquifer Question 1. Water will be supplied with pump from a well in…

A: Given Hydraulic conductivity k=0.003 m/sand maximum velocity of flowVmax=k30=0.00330=0.01…

Q: Calculate the discharge in the concrete trapezoidal channel if the slope is 0.0002, the side slope…

Q: A well of 0.5 m diameter penetrates an unconfined aquifer with thickness of H below the static water…

A: To find Transmissivity T and radius of influence R

Q: 3. A hydraulic jump is to be formed in a channel carrying a discharge of 0.8 m³/s/m width of channel…

Q: (400 gpm). 9.16. Determine the maximum steady-state pumping rate in lps (gpm) for a 305-mm (12-in)…

Q: 1. Three wells each having a diameter of 250mm are installed at the vertices of an equilateral…

A: Given Diameter of well =250mmrwell=2502=125 mm=.125mVertices of an equilateral triangle=18 m∆h=2.5…

Q: A test well with a diameter of 350mm reached 27 meters below the static water table. The water table…

Q: determine the critical depth of a trapezoidal channel conveying 1.33 cumecs of fluid .The base of…

Q: EXAMPLE 1: Determine the normal discharge for the channel shown in Fig 2.7a. The water surface in…

A: Discharge is the volumetric flow rate of water that is transported through a given cross-sectional…

Q: At one section of a 300 cm wide rectangular channel, the depth of flow is 180 cm. With a bed of…

Q: For steady state flow to a fully penetrating well in a confined aquifer, the drawdown at radial…

A: Solution is attached below as

Q: The radius from the observation well A and B are 150 ft and 300 ft, respectively. The thickness of…

A: The radius of well A (Ra ) = 150ft The radius of well B (Rb) = 300ft Depth of aquifer (D) = 100ft…

Q: Question- Three tube wells of 25 cm, diameter each are located at the three vertices of an…

A: Given- Three tube wellsDiameter =25 cmSide of equilateral triangle=100 mradius of influence R=300…

Q: What is the critical depth in a rectangular channel with 2.3 m width and 0.91 m2/s discharge per…

A: What is the critical depth in a rectangular channel and calculate minimum specific energy?

Q: at a depth of 360 mm. A hydraulic jump occurs and the depth of water downstream from the

A: Given data- Width(B) = 5m Depth(y1) = 360 mm = 0.36 m Hydraulic jump(y2) = 1300 mm = 1.3 m

Q: Calculate the discharge in the concrete trapezoidal channel if the slope is 0.0002, the side slope…

Q: A 50 dm diameter well gives a discharge of 0.05 m³/sec. Two observations well were made at a…

A: Given data, q = 0.05 m³/s B = 10 m Diameter of well = 5 meter

Q: Two pipes are connected in parallel between two reservoirs: L1= 2000 m, D1= 160 cm, C1=120; L2= 1400…

A: Given: Two pipes connected in parallel,L1 = 2000 m L2 = 1400 mD1 = 160 cm D2 = 800 mmC1 = 120…

Q: A 900 mm diameter pipe 1,800 m long carries 1.2 cu.m./sec from reservoir A, whose water surface is…

Q: Question: Open channel test is performed and according to the following; (t=14.35 s)(1kg = 0.01m3)…

A: t=1 kg =y=B=To find- a) Flow calculationb) Energy from the flow ratec) Energy by point velocities

Q: The following criteria are needed to reach the "steady state" EXCEPT.. i. The water level in the…

A: The following criteria are needed to reach the "steady state" EXCEPT.. iv. The water level in all…

Q: Q.17.7 A reservoir discharges through a sluice 0.915 m wide by 1.22 m deep. The top of the opening…

Q: Estimate the transmissivity of confined - aquifer in steady state flow if you know the drawdown is 3…

A: S1=5m S2=3m rw=2m r2=30m

Q: 0cm diameter well fully penetrates an unconfined aquifer with saturate thickness ho-60m and…

A: GIVEN DATA:-⇒Diameter of well dw= 30 cm⇒radius of well rw= 302⇒rw=15 cm⇒Thickness ho= 60m⇒ro= 120…

Q: A pump out test is carried out in a perforated well of 30 cm in diameter, extending into an…

Q: A well with diameter of 42cm fully penetrates 32m below the static water table. After 24 hours of…

A: Given,Radius of well, rw = 0.422 = 0.21 mDischarge, Q = 6 m3/min = 660 m3/sec = 0.1 m3/secAt rw =…

Q: The static level of water table in an unconfined aquifer was 35m above the underlying impermeable…

Q: Two identical groundwater pumps are operating 4.2 km apart. Each pump well structure has a tube…

Q: Q2) A flocculation basin has dimensions of 17.4m length, 11.4m width, and 5.8m depth, with three…

Q: A 50 dm diameter well gives a discharge of 0.05 m³/sec. Two observations well were made at a…

Q: Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3

Q: The elevations of the three-reservoir system are shown in the figure. Considering the pipe data…

A: Given:- The elevation of reservoir A = 150 m The elevation of reservoir B = 120 m The elevation of…

Q: A bulk storage tank is leaking and a well nearby is being pumped to try and contain the leak. K=5…

A: To calculate the parameters for the capture zone of a pumping well, we need to use the formula for…

Q: 2. It is known that an irrigation channel has a rectangle with width (b) = 4.5 m, height (h) = 5 m,…

Concept explainers

Issues During Construction

Construction is the combination of art, science, and engineering to build buildings, bridges, structures, roadways, highways. airports, etc. The construction business is a challenging and promising business worldwide with certain risk factors involved. Increasing demand for mankind leads to the growth of several construction companies which specialize in different construction projects. These construction companies initiate their construction process under certain agreements and time durations called the construction contract.

Question

Calculate the drawdown in a drainage well having a radius of (50cm), with a lowering in water,
table at point P1 at a distance of (100m) from the well of (1m) lowering, and a lowering of
(4m) at point P2 with a distance of (40m)from the well. Saturated thickness is (40m) while
pumping is 2000 m³/d.
h

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of permeability

VIEW

Step 3: Calculation of drawdown in drainage well

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question- Three tube wells of 25 cm, diameter each are located at the three vertices of an equilateral triangle of side 100 m. Each tube well penetrates fully in a confined aquifer of thickness 25 m. Assume the radius of influence for these wells and the coefficient of permeability of the aquifer as 300 m and 40 m/day respectively. Calculate the discharge when only one well is pumping with a drawdown of 3 m. (i) (ii) (iii) What will be the percent change in discharge of this well if all the three wells were to pump such that the drawdown is 3 m in all the wells?
(b) Give the characteristics of different formations in which groundwater exists. A fully penetrating artesian well is discharging at a rate of 25 litres/sec. The storage coefficient and transmissivity of the aquifer are 4.5 × 104 and 0.15 m²/min respectively. Find the drawdown at (i) A radius of 5 m distance after 2 hours pumping. (ii) A radius of 150m distance after one day pumping. Use the following approximation well function W(u) = -0.5772 - In(u) - u.
Exercise 4-3 (Problem ?? pp. ??) A single ideal pumping well, with radius of 1.0 ft and flow rate of 155 gpm, exists in an ideal confined aquifer. The aquifer has a saturated thickness of 82 ft. The pump continues running until equilibrium conditions are reached. The drawdown at the pumping well is 42 ft, and the drawdown at an observation well 138 ft away is 7.5 ft. Determine: ft² 1. Find the transmissivity in and hydraulic conductivity in 2. Find the radius of influence in feet.
Irrigation and drainage, i need solutions in 15 minutes please. MCQ/A 30 cm diameter well completely penetrates a confined aquifer of permeability of 45 m/day. The thickness of the aquifer is 20 m. Under steady state of pumping the drawdown at the well found to be 3.0 m and the radius of influence was 300 m. Calculate the discharge of the well . A-0.0851 m³/min B-1.548 m³/min C-0.0258 m³/min D-0.258 m³/min
A well of 0.1 m radius is part of a wellpoint network to keep an excavation dry. The groundwater at the far edge of the excavation must be 0.5 m below the base. The radius of influence is and the maximum drawdown is 6.18 m. For the radius of influnce calculate the discharge if the well radius increase to 0.2 m, and compare it to the discharge for the 0.1 m radius well.
Please answer question 9.16 ASAP
A 30 cm well is pumped at the rate of 1000 ipm. The transmissibility of the aquifer is o.015 m²/s. If the well is located at a distance of 120 m from a stream, what should be the drawdown? (i) In the pumping well- (ii) In an observation well 80 m away from the pumping well on the side opposite to the stream? (iii) In an observation well 80 m away from the pumping well, on a line parallel to the stream?
For the standpipe shown, determine the discharge for the following depths. C = Cart = 0.6. a. 1m b. 1.5 m C. 2.1 m d. 2.4 m e. 2.5 m 1m 0.9 m 2m 1.2 m 0.8 m
Assume uniform flow through a half-full circular channel. a. hydraulic radius (m) b. Reynolds number c. hydraulic depth (m) d. Froude number
Please answer the question with all conversion being in feet
Question 4 Calculate the discharge (m³/day) through an infiltration gallery placed at a depth of 4m below ground water table, subjected to the condition that the drawdown in the well does not exceed 2.18 m. Take the length of the gallery 56.75 m and radius of influence to be 100m. The hydraulic conductivity can be assumed as 75 m/day.
A 300-mm diameter test well penetrates 27 m below the Water is pumped at for 24 hrs. The observation wells 35 m and 95 m from the test well were of static liters per 69 two water table. a rate second water levels at lowered by 1.10 m and 0.50 m, respectively. a. Compute the flow rate in MLD (megaliters per day). b. Compute aquifer. c. Compute the transmissivity of the coefficient of permeability of the the aquifer. Use the q In T = 2π (h2-h1) formula