Calculate the distance (y) to the centroid C of the channel section shown in the figure if a=150mm, b=25mm, c=50mm And also calculate the moment of inertia (Ixc) with respect to an axis that passes through the centroid C and is parallel to the x-axis

Q: Q2: For the beam shown in figur , determine the value of I that will limit the maximum deflection to…

A: let,RA=vertical reaction at A in upward directionHA=horizontal reaction at A in inward…

Q: Calculate the deflection at the center of a simply supported beam in mm, if the beam has a length…

A: Given data- EI=4.5 m4 Pa

Q: Given the figure, find the tension at A, B, C, D in Newton. The other photo is the continuation of…

A:

Q: In the fig. shown, compute the following: (a) Components of the centroid ; ỹ = (b) The total moment…

A: To determine of the coordinates of the centroid and the moment of inertia about the centroidal…

Q: A beam of length 6m is supported at its ends and carries UDL 0f intensity 28as shown in fig.…

A: Support Reactions :  ∑Fy = 0RA + RB = 28×4 = 112 kN ..............(1)Taking Moment about A, MA =…

Q: 1.52 m 2.1m ー斗 子om 2.28 m 7m

A:

Q: Refer to the figure shown a = 11.7 x 10/°c E = 200 GPa A = 1,200 mm2 a = 23 x 10/°C E = 70 GPa A =…

A:

Q: Determine the polar radius of gyration about point A for the shaded area shown. 56 mm 56 mm 43 mm…

A:

Q: 22 - Find the center of gravity M of the three dimensional homogeneous wire ABCD using the…

A: bfrom the figureABX1,Y1,Z1=36,12,0L1=24BCX2,Y2,Z2=24,24,12  L2=24CDX3,Y3,Z3=18,24,24  L3=36

Q: Determine the location of the centroid, y, and the moment of inertia of the cross section about the…

A: First calculate the area, y coordinator of centroid and moment of inertia about Centroidal x-axis of…

Q: Q3| For the beam shown in Fig. (3); ( El is constants ): A - Compute the slope of the elastic curve…

A:

Q: Determine the vertical deflection at B

A:

Q: For the figure shown knowing that a = 1.00 cm and b = 4.00 cm, determine: a) The centroid of the…

A:

Q: Deflection of Beams 1. Determine the midspan deflection of the beam if E = 10 GPa and I= 20 × 10°…

A: Given data: E=10 GPaI=20×106 mm4EI=10×106×20×10-6 kN.m2EI=200 kN.m2

Q: 600 N/m- 1m 2 m

A:

Q: An aluminum bar of cross-section 450 mm2 is acted upon by the forces as shown in the figure.…

A:

Q: Determine the horizontal deflection of D. Fy-20.00 B Fx=10.08 3.0 m A C 4.0 m D 3.0 m Consider the…

A:

Q: Determine the value of the deflection at B in mm. Answer in 2 decimals 2 kN/m Br E = 200,000 MPa 3m…

A: Given that...

Q: -2) Determine the coordinates of the centroid of the area shown with respect to the given axis.

A: Find co-ordinates of the Centroid in the above problems

Q: A beam with span of 12 m has overhanging portions at both ends and is loaded with a uniform…

A:

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A:

Q: 4) Calculate the location of the centroid of area (X,Y) and the moment of inertia about the center…

A:

Q: A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3…

A: We have to find the general deflection equation of the given beam

Q: 1bomm

A:

Q: A solid metal bar of uniform sectional area throughout its length hangs vertically from its upper…

A: given Length L=6 mdensity =8×10-5 N/mm3E=2×105 N/mm2

Q: Determine the magnitude of the reactions on the beam at B. Neglect the thickness of the beam. 2…

A: Finding out magnitude at B.

Q: 14 - Obtain the center of gravity of the surface area of the constant thickness plane plate in the…

A:

Q: Using Double Integration Method Calculate the deflection at the free end of the beam shown below.…

A:

Q: A cantilever beam supports a uniformly varying shown in the figure. If EI = 300.65 kN - m², detern…

A:

Q: 3. The following figure shows a portal frame. Draw all modes of failure. And determine the plastic…

A: Solution Explanation and complete solution of the above equation is in the second step

Q: Using conjugate beam method calculate for the moment of inertia for the beam shown below so that the…

A:

Q: For the cantilever beam shown in the figure, what will cause zero deflection at A? ANS. P=112.5 A P…

A:

Q: 15 mm 15 mm 15 mm C

A: Divide the given section into three parts as shown in the below image: a = 210mm  b= 280mm c =…

Q: In the figure shown, each of the four vertical links connecting the two rigid horizontal members is…

A:

Q: A simply supported steel beam with a length of 10 m carries a superimposed uniformly distributed…

A: Moment of Inertia =  540 x 106 mm4  Length of Beam = 10m  Allowable deflection = L/240  Beam weight…

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A:

Q: Analyze the frame shown below D 120 kN- 4m B 3m - 5m El = constant (a) Frame D ID WCD BD B 3.

A:

Q: 100 mm 200 mm 100 mm 300 mm

A: Given Area:

Q: Determine the slope at point B of the beam in the figure below. Assume the material's modulus of…

A:

Q: solve step by step in digital format Solve the following exercises by the conjugate beam method A…

A: A cantilever beam is given with UVL load zero at free end and 6k/ft at the fixed end.The span of the…

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.