Calculate the depth d in which the discharge (Q=1.5 m/sec) will flow through the channel with trapezoid-shaped cross section. Width of the channel bed is (b =2 m), slope of bed (S=0.05%), sides slope is (Z=1.5). The channel is excavated in gravel sends in which the roughness coefficient is (n =0.0247).

Calculate the depth d in which the discharge (Q=1.5 m/sec) will flow through the channel with trapezoid-shaped cross section. Width of the channel bed is (b =2 m), slope of bed (S=0.05%), sides slope is (Z=1.5). The channel is excavated in gravel sends in which the roughness coefficient is (n =0.0247).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1- A 2 m wide rectangular channel (n=0.015), carries a discharge of 6 m³/s. The channel is laid on slope of 0.0162. The channel width and slope changed to 1.5 m and 0.0122, respectively. (a) Calculate critical and normal depths. (b) Calculate Froude numbers. (c) Plot the water surface profile. 2- Sketch and label the type of water surface profile in (a), (b) and (c). (a) (b) (c) TTTTTTTTT L n (Small) n (Large) TTTTTTT NDL NDL CDL NDL CDL NDL MITT
Q2. Discharge in a wide rectangular open channel can be found using the Manning's 0.5 roughness formulation of - AR067 S. ° where Q is the discharge, n is the roughness coefficient, A is the cross-sectional area; R is the hydraulic radius, and S, is the bed slope. Given that R = h (flow depth), and A = 12h, and S, = 0.0025 and n = 0.0125; Compute the flow depth (h) when Q = 120 m³/s, using the Newton's method. Start with ho =2 m initial guess and perform only a single iteration. Winc Windo
Q- A rectangular open channel has a width of 5m and a bed slope of 0.001. For a uniform flow of depth 2m, the velocity is 2m/s. The Manning's roughness coefficient for the channel is.
A box culvert, as shown in the figure, was designed to carry a discharge (Q m'is) from a square channel. Manning coefficient for channel and culvert is 0.015. The longitudinal slope of channel is 0.0000s. The length of the culvert is 75m, K.- 0.16, and Ke = 1.0. y of soil y, = 1.6 ton/m y of conc. ye- 24 ton/m y of water yw=1.0 ton/m Use 40 ton for L.L If the entrance of culvert is full submerged: - 1. What is the diameter of the culvert (use 1 dig only)? 2. What is the total head loss along the culvert (use 3 digs only)? 3. What is the total load on Top of the culvert (use 2 digs only)? ( Earth Filling 0.2Y
Design a trapezoidal open channel (n=0.014) that is anticipated to convey 20cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic radius of the designed section.
Determine the hydraulic radius for the following rectangular open channel: Width = 29m Water depth=7m
Solve fast like within 30 minutes.
A trapezoidal channel with side slope of 2H-1V has a flow rate of 180 m3/s and depth of 4 meters. The slope is 1m per kilometer. Determine corresponding bottom width in meters. The correct answer is 21.06 Pls show me the solution
Design a semi-circular open channel (n=0.014) that is anticipated to convey 20cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic radius of the designed section.
For the channel (Consider a rectangular channel 3 m wide laid on a 1°slope. If the water depth is 2 m, the hydraulic radius is), if the water depth is 2 mand the uniform flow rate is 24 m3/s, what is the approximatevalue of Manning’s roughness factor n?(a) 0.015, (b) 0.020, (c) 0.025, (d ) 0.030, (e) 0.035
Design a semi-circular open channel (n=0.014) that is anticipated to convey 25cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic depth of the designed section.
3. A rectangular box culvert has a 90º headwall with 33.7º bevels, and the inlet is mitered. The width of the culvert is b = 4 ft and the height is d=5 ft. The culvert is 100 m long with a slope of S = 0.01. Prepare a plot of HW versus Q for this culvert if it is to operate under inlet control.