Calculate the components of the forces at B and C. A P B D Given: P = 20 kN a = 1.1 m b = 1.3 m c= 1.3 m d = 1.2 m 8 = 32° Required: By = kN Bx = kN Cy = kN Cx = kN

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: FIND THE GENERAL SOLUTION (Do+2D² -15D)y=D0

A:

Q: (Q3) If the magnetic bearing of line ED is (aED= N45%80c95c W) in the below drawing, compute…

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A: E = 12 GPa Use virtual method to analyze the beam.

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: Assignment 2.: A line CD, 60mm long, is perpendicular to VP and parallel to HP. It is 20 mm above…

A:

Q: Examp;e: The following Figure with two projections, assign the types of these projections and draw…

A: The type of projection is first angle projection. The view shown below are  front view and right…

Q: Write the formula for the effective length factor?

A: The effective length factors of columns  plays major role in the design of compression members.…

Q: ARSWer ls With reference to the units systems, One full circle equals 400 Grades 180 15 30 2 TT

A: One Full Circle equals to 400 GRADES  And also 2π radians and 360°

Q: III. DETERMINE TOTAL AREA USING DMD METHOD. , L = 11.25 m L = 9.20 m L = 6.40 m L = 9.25 m B =S 79°…

A:

Q: What is the Length between STA 50+100 and STA 50+120? Please explain

A:

Q: Q25. Draw the plan, section and elevation of the given line diagram. BАTH 2000 x 2500 BED 5000 x…

A:

Q: where did you get the values of tp=17.27 & do=24 ??

A: Given question,  How to get values of tp and do = ?

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: - 4- पिक (17 b=260m- de-Sm h= 300m = 204N/m to 2onm M= <40kN b f=30kW

A: Given. Udl =20kn/m bending moment 40knm Point load 30kn Draw sfd bmd

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: Describe the structure of the surveyor’s compass.

A: The large surface when undulated the process used for surveying is known as surveyor's compass.

Q: Locate the X–X and Y–Y centroidal axes for the area shown.

A:

Q: How did you get -7.5x2+0.417x3 for M1? Thank you for answering.

A: The triangular load can be assumed to be superposition of a downward uniform load and upward…

Q: Which shape has more sides than a quadrilateral?

A: A polygon is a two-dimensional shape that is formed by a set of line segments forming an enclosed…

Q: What is the elevation of point C?

A:

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: Why is the F1y = 400lb?

A:

Q: Can you please explain further where did you get the tan theta = 4/3?

A: Truss

Q: St BS 0+00 3.54 0+10/ 0+20 1 1 1 1 I 2.994 2.044 0.171 00249 1.497 IS 3.269 2.966 Fs 1.845 1.840…

A:

Q: 10 20 10 +¹0| -25 30 20, 70 Dimensions in millimeters x Break the shaded area into the five…

A:

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: Need clear and complete solutions. Determine the coordinates of the centroid of the shaded area. 10…

A: Given data

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: May I ask where did 45 N in step 1 come from?

A: It has been given that to ask explanation in 1st step in solved problem. Please refer step 2 for…

Q: Compute the Interior C. Compute the Interior B. Compute the Interior A. Compute the Interior D

A: Given Data- To Find- Internal Angles A,B,C &amp; D

Q: Problem No. 4 Given below is the technical description of a lot F. lines Distances (m) bearings S…

A:

Q: SITUATION 05 At a height of 10 km above sea level, a building 38 m by 45 m is to be laid out with a…

A:

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: Convert 109° 46' 51" to degree decimals. Round your answer to 3 decimal places. Do not include units…

A: To convert in degree decimal

Q: The Surface Area Calculation,

A: True

Q: End Area (ft2) Volume (yd) Volume (yd) Net Volume (yd) Station Mass Shrinkage Total Cut Fill Cut…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Input values only without…

A: A section have been given and it has been asked to determine centroid of the section. Please refer…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.