Calculate the break horsepower of a pump with a volumetric flow rate of 20 gallons per minute.

Q: The force required to slip one layer of a fluid past another with a given velocity is * O Rate of…

A:

Q: 2 cfs of water is pumped through the 45° vertical pipe bend in the 6 inch diameter pipeline shown…

A: we'll use reynolds transport theorem

Q: How we can calculate friction losses due to changes in velocity and direction in side a conduit

A: Friction losses due to changes in velocity and direction in side a conduit can be calculated as

Q: Q2 // The diameter of a pipe at section 1 and 2 are 10 cm and 15 cm respectively. Given velocity of…

A: Given that, The diameter of the pipe at section 1 D1 = 10 cm = 0.1 m The diameter of the pipe at…

Q: A solid cylinder of weight 9 kg slides in a vertical lubricated pipe. The clearance between the…

A:

Q: Write down the 2 key parameters that affect the friction losses of the fluid flowing through a…

A:

Q: Explain flow rate in relation to fluid mechanics

A:

Q: Rate of movement of fluid passing one another. * O surface tension Shear O Rate of shear O Viscosity

A:

Q: 3-foot-long, 8-inch-diameter cylinder inside a 25.8-inch-diameter tube at 3 feet per second. Fluid…

A: Given data: Length of pipe= 3ft Kinematic viscosity=0.006 ft2/s Constant velocity=3fps  Relative…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds? When the…

A: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds?= for laminar…

Q: Brine (SG = 1.1) is flowing through a 100-mm ID smooth pipe at a Reynolds number of 48000. The…

A:

Q: This factor is usually neglected on calculation for pressure drop. A Acceleration B Elevation…

A: Pressure Drop: Difference of total pressure between two point in a fluid flow network is called…

Q: 4. Water flows through a smooth horizontal 2 m long tube of 2 mm diameter with an average velocity…

A:

Q: Determine the pressure drop across the orifice meter as shown in Example Figure

A: Given,  ρ1 = 1000 kg/m3 d=0.022 m ρf=1100 kg/m3

Q: As flow meters, these devices mechanically divide a fluid stream into discrete, known volumes and…

A:

Q: Unit for mass flow rate and molar flow rate

A: The mass flow rate is defined as the differential mass of the fluid flowing per unit of time. The…

Q: 1. A flow rate of 16 m/(m² h) is maintained through a 0.6-m-deep bed of filter sand. The sand is…

A: Given: Velocity in bed V = 16 (m3/m2.h) = 16 m/h = 163600m/s = 0.0044 m/s diameter d = 0.4 mm =…

Q: Write a report detailing the energy balance in pumps, with illustrations, formulas, and diagrams and…

A: A pump is used to move liquids with the help of the pressure difference between one point and the…

Q: In a gyratory crusher the size reduction is effected primarily by: 1.impact 2.attrition 3.cutting…

A: This question is based on crushing and grinding operations. We will analyse each option and find the…

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0064 m.…

A:

Q: What Is The General Balance Equation?

A: Energy is defined as the ability or capacity to do work. There are various forms of energy, for…

Q: Calculate the cross-sectional mean velocity of water flow in a pipe. The pipe diameter is 5.0 mm,…

A:

Q: A centrifuge bowl shall separate 2 immiscible liq, SG = 1.1 & SG = 0.9  The diameter inside of the…

A: Given Data  The specific gravity of the two immiscible liquids are given  as :SG = 1.1 , Therefore,…

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: 5.1-2. Frictional Pressure Drop in a Flow of Olive Oil. Calculate the frictional pressure drop in…

A: Olive oil density and viscosity at a given temperature are obtained. The Reynolds number is…

Q: As flowmeters, these devices are most widely used. They most often also have ★ integral temperature…

A: As flowmeters, these devices are most widely used. They most often also have integral temperature…

Q: Calculate the net force acting on the cone in Figure 4.69. Im Water 3 m Figure 4.69 System for…

A:

Q: How much error do you think you will have in the actual end-to-end pressure drop when designing a…

A: This question is based on fluid dynamics We have to analyze the end to end pressure drop while…

Q: The U tube shown is rotated about the left vertical leg at 30 rpm. The pressure at point A is…

A:

Q: Define shear stress and it’s relation with dVx/dy for a Newtonian fluid

A: Shear stress is an important factor in the study of various types of fluids.

Q: An oil is used to lubricate a thin plate with a surface area of 5.382 ft? that is placed between two…

A: Given that, The surface area of the thin plate A = 5.382 ft2 = 0.5 m2 The distance between the two…

Q: Which of the cross-sections below would experience the lowest engineering stress when the same load…

A: Engineering stress is defined as, Engineering stress = Force appliedcross-sectional area let us…

Q: a water pipe with an inner diameter of 2 cm carries 2X10 ^ 5 pa water at a speed of 1 m / s.…

A:

Q: Discuss in detail (Diagram, Working and Application) about any one Flow measuring devices

A: The flow measuring device is the device that is inserted into the flowing fluid that produces a…

Q: At 30c glycerin (viscosity = 0.5 N.sec/m2 ,density =1260 gm/cm, flows at a rats of 180 ml/min…

A: Laminar flow or streamline flow in pipes occurs when a fluid flows in parallel layers, with no…

Q: A cylindrical pressure vessel of radius r = 10.2 in is filled with a gas at a pressure of 455.0 psi…

A: As given  Maximum force on bolt that can withstand = 32505lbf Net force exerted on each bolt holding…

Q: In a large student house in Sheffield, cold water is supplied by the mains water supply at a…

A: The Reynolds number and type of flow is to be mentioned for the fluid given.

Q: perpendicular to the surface eccentricity center of piezometric depth pressure head The direction of…

A:

Q: A device used to move incompressible fluids is known as O pump O blower O compressor Ca9FRed with…

A: Incompressible fluid is one where density remains constant. If fluid doesn't change volume than any…