Calculate the analog input to a 4bit ADC with a reference voltage range of +5 V to OV when the digital binary output is 0110. O 0.63 V O 1.98 V O 4.25 V O 2.11 V

Q: Assuming a JFET has an Ipss = 9 mA and VGs(off) = -8 V (maximum). Using these values, determine the…

A: By drain current equation we will find out drain current .

Q: Please solve the problem

A:

Q: Symbol of SCR

A:

Q: secting the SCRS top two & bottom two laye isecting the SCR vertically secting the SCRS middle two…

A: In this question , we have to write about how two transistor model of SCR obtained..

Q: Consider a 9.4-bit ADC and full scale voltage measurement range of (-41V to 41V).The Resolution will…

A: Resolution is given by  R = Dynamic Range / total number of steps  Resolution = Dynamic Range /…

Q: Determine the required resolution for analog to digital converter with 24 bits of word length if t…

A:

Q: Design a 3bit flash A/D converter

A:

Q: Analyze the changes in the output of thermistor sensor (with negative temperature coefficient) when…

A: For a thermistor Input quantity : temperature  Output quantity : resistance

Q: fullwave bridge type rectifier whose transformation ratio is 10:1 for an

A:

Q: Assuming a JFET has an Ipss = 5 mA and VGs(off) = -7 V (maximum). Using these values, determine the…

A: By drain current equation we will find out drain current.

Q: What is Quiescent? What does it mean a transistor in saturation?

A: Quiescent point: The constant Dc voltage or current at a certain terminal of an active device, such…

Q: - Design a flash ADC with input voltage range [ igital output for a 2.5 V input signal?

A:

Q: Determine the gate trigger current and the anode current when the switch, SW1, is momentarily closed…

A:

Q: Peripheral lo is used by processors. Motorola Intel Interrupt RISC

A: Peripheral IO: In this I/O interfacing, the I/O devices treated as differently from memory chips. In…

Q: Draw a low level AM circuits (transistor based)

A: Types of Amplitude Modulation   Single sideband modulation Double sideband suppressed carrier…

Q: For 4-bit DAC Binary Weighted Resistor Method, if the Vref = 20V, and R = 5 Kohm, what is the output…

A: In this question we need to find a output current for the sequence 1001

Q: IC 7408 consist of Four, Two input AND gates SIX, ONE input NOT gates Four, Two input OR gates SIX,…

A:

Q: A 12- bit ADC has an input range of 0 to 5 V. What will be the maximum percentage quantisation error…

A:

Q: 2. Design a center-tapped full wave rectifier circuit. Use a 4.7 ka load resistor. Find the…

A: Here Vp is peak  voltage.

Q: Interpret the following bridge rectifier (include PIV) 2) Find the voltage and current at position…

A: The solution can be achieved as follows.

Q: (1) R₂ C₁ DIS TRI THR VCC C₂ 100 nF 555 Timer CV RST Figure 4(b) OUT GND I V cc V out 12 V The…

A:

Q: The purpose of analog low pass filer at the input of DSP system is to band limit the input signal.

A: A low-pass filters a filter that passes signals with a frequency lower than a selected cutoff…

Q: What is the required input voltage at AREF pin in Arduino UNO to have LSB voltage resolution of 1.47…

A: Given, Resolution of Arduino Uno is 1.47 mV. The Arduino Uno ADC is of 10 bit resolutions.

Q: For an N-channel JFET Idss = 8mA and Vp = -6V, if Vgs = -2V then what is the value of the Drain…

A:

Q: The ----- terminal of the JFET is the equivalent of the base terminal of a BJT. O a. Drain O b. Gate…

A: ....terminal of the JFET is equivalent to the base terminal of a BJT.

Q: For an analog to digital conversion using 10 bits in a O to 5 volt range, what is the precision or…

A:

Q: dipha O 400 O 40 O 4 O 0.4 The RMS output voltage of a Full-Wave Bridge Rectifier is 20 volts,…

A: In this we will find beeta value, avg current of rectifier...

Q: The diodes in the circuit in the adjacent circuit have piecewise linear parameters of Vy = 0.6 V and…

A: The circuit diagram is shown below,

Q: The smallest input voltage recognized by the ADC converter is the Select one: O superior O…

A:

Q: Consider a 5-bit ADC and full scale voltage measurement range of (-41 to 41).The Resolution will be…

A:

Q: A) Write the instructions for the following scenario: - Read two numbers from input ports (10,11).…

A: Note: since Part B of the question is based on software, hence we will only solved part A for you.…

Q: In a GTO, anode current begins to fall when gate current

A: Given: In a GTO, anode current begins to fall when gate current.

Q: The logical 1 input to an AND gate 74LS08 is a 1 Volt signal a 5 Volt signal a 15 Volt signal

A: 1)74LS08 is a high speed AND gate IC.. 2) The input voltage for a logic HIGH is around 5 volt DC…

Q: EXAMPLE 3 Determine the gate trigger current and the anode current when the switch, SW1,is…

A: The solution can be achieved as follows.

Q: For 4-bit DAC Binary Weighted Resistor Method, if the Vref = 20 what is the output current for the…

A:

Q: Q1: Determine all the output waveforms for the 74HC195 when its input signals are shown below CLK J…

A: Given data: Waveforms for Input signals to a 74HC195 IC are given, CLK, J, K', SH/LD', CLR', D0, D1,…

Q: self-bias circuit of Figi

A:

Q: Consider a 3-bit ADC and full scale voltage measurement range of (0-56) The Resolution will be O…

A:

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.