Calculate installed capacity, expected annual energy generation, and the capacity factor.

Q: single hydraulic turbine is to be selected for a power site with a net head of 30 m. 10 700

A:

Q: Pravinbhai

A: The objective of the question is to calculate the required power of the pump in kilowatts (kW).

Q: A 5000 N weight is pulled up on an inclined surface at a constant speed by a cylinder as shown in…

A:

Q: Parvinbhai

A: The objective of the question is to calculate the maximum torque that a hydraulic motor can generate…

Q: A 10-hp pump (installed a the ground level) draws water from a well 30 ft below ground level ane…

A:

Q: Solve step by step Q3. In a Parsons turbine running at 1500 rpm the available enthalpy drop for an…

A: Given Data: Speed of turbine N=1500 rpm Enthalpy drop in expansion of steam ∆H=60 kJ/kg Mean…

Q: 1. For a hydraulic motor, its displacement Vp-250ml/r, the inlet and outlet pressure are 9.8MPa and…

A: Given: The displacement of the motor: →VP=250 ml/r=0.25×10-3 m3/r Inlet pressure→Pi=0.49 MPa Outlet…

Q: Q3: Brayton Cycle consists of several processes, explain them with aid of drawings

A: Brayton cycle is a thermal cycle that uses heat energy of air (heated in combustion chamber by…

Q: Q5) A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the…

A: Here the Figure are consider for Determining

Q: A hydraulic pump delivers 14 litres per minute towards pressure of 200 bar.Find the following  (a)…

A: Given - Flow rate (Q) = 14 litres per minute = 2.33 x 10-4 m3/s Pressure supplied (P) = 200 bar = 2…

Q: Q) A shaft has a number of collars, external diameter of each is 35 cm and the shaft diameter is 20…

A:

Q: exhaust= Fluid leaves 400°C @34 mPa Bojter Tui bine I Pump efficieney= 0.80 = 80"/- Info: broiler…

A: Given data Turbine inlet conditions are : 4 MPa and 400°CTurbine exhaust conditions are : 10 kPaPump…

Q: Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net…

A: Given, net head, H=65mRPM, N=700rpmBHP=400KWB1D1=0.1D1D2=0.5ηh=0.94ηo=0.85flow ratio, φ=0.18 At…

Q: Problem 1: Water is flowing in steady statę through the elbow shown in the figure. Assume the…

A: Given data as per question A1 = 2 m2 A2 = 1 m2 V1 = 10 m/s

Q: For the hydraulic motor in the following figure, geometric volume is 10ml/r, working pressure…

A: Disclaimer: Since you have posted a question with multiple sub-part, we will solve the first three…

Q: Determine the power generated in MW by the hydroelectric plant with the following given: Head water…

A: Given:Head water level, z1=120 mTail water level, z2=46 mHead loss, hl=4 mFlow rate, Q=66…

Q: Q4: Find the force required to hold the blade in position, if the jet weight (100kg) and discharge…

A:

Q: Q2 .. h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump…

A:

Q: HGL Elevatior - 10 D- 30 cm Elevation-6 m 40 cm diameter Water T- 10-C Elevation - 2 m EGL HGL…

A: Option first is correct.

Q: A double-acting cylinder has a plunger of 10 cm in diameter. The diameter ratio between the plunger…

A: Given: The diameter of plunger, D = 10 cm The diameter ratio between plunger and stem, D/d = 5 The…

Q: A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: 4.) Consider a large industrial HVAC duct with a diameter of 1 m that flows air at a pressure of 100…

A:

Q: e power developed by the turbine.

A: To find Flow velocity Power developed

Q: ermine the torque require steady state if it is free to

A: given:

Q: A turbine extracts water from a 25 m high reservoir, if the flow requirement is 10000 m3/hr, what is…

A:

Q: A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of…

A: Given , Pelton wheel  mass flow rate =  6kg/s velocity v1 =  70m/s. deflection angle = 165º mean…

Q: Find the cam diameter and actua volume displaced? Jolumetric efficiency 1420 rpm, e = 14.67 mm, L…

A:

Q: Verify the design of the San Francisquito power plant, which has the following specifications:…

A: Given: water power→p=32200 hp=32200×3300060=1771×104 ft poundsec head of the plant→H=800ft so…

Q: Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net…

A: Given that H=65 m , N=700 rpm , BHP=400 , ηH=0.94 ;ηo=0.85 ;⇒wheel width at inletwheel diameter at…

Q: Pelton wheel has to be designed for Hydroelectric power station by taking the following…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.