A tank is full of water. Find the work W required to pump the water out of the spout. (Use 9.8 m/s² for g. Use 1000 kg/m³ as the weight density of water. Assume that a = 4 m, b = 4 m, c = 12 m, and d = 3 m.) W = נן TALIBA

A tank is full of water. Find the work W required to pump the water out of the spout. (Use 9.8 m/s² for g. Use 1000 kg/m³ as the weight density of water. Assume that a = 4 m, b = 4 m, c = 12 m, and d = 3 m.) W = נן TALIBA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
Phy
1. What is the boundary not for? A. Separate the system from the surrounding. B. Create a definite region and space C. Contain energy and mass as it flows D. Signifies a control volume 2. Which statements describe steady-state-steady-flow system? A. Permit the flow of energy and mass into and out of the system B. Energy contained by the system changes over time C. Energy contained by the system is constant as different kinds of energy enter and exits it. D. All of the above * explain the answer
10.A balloon envelope has a volume of 3000 m3 . Take the density of ambient air as 1.2 kg m-3 and the density of air in the balloon as 0.95 kg m-3 . Find the net upthrust and hence the maximum mass of the balloon and payload.
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
Q2:- In figure ax=4.903 m/s , ay=9.806 m/s*.Find the pressure at A,B,and C as shown in fig.2 ay A 300 mm ax 1 m Water B 1.3 m Fig.2
The total volume of the water tank used in the equipment is 0.02 m3", and the water is heated through the heating rod. The efficiency of the water circulator 40W is 40%, and the remaining energy is released as heat. Given that the heat lost in the entire area in contact with the outside is KI(T-Ta)dT, find the following. O 25 °C → 30 °C. 2 30 °C → 35 °C (C.=4.184J/ml-C, Ta=20 °C. K = 10 J/s-C) (1) Energy balance: equation (2) Total energy used by Heating rod (J)
A pump is supplying water at the rate of 4ft^3/s it lifts water to a height of 15ft. Determinte the power that the water is being delivered to by the pump (hp). If the pump has 80% efficiency , find the power that needs to be supplied to the pump (hp)
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, ρ1=1300 kgm/m3. At exit: A2=10 m2, ʋ2=0.00125 m3/kg, ῡ2=3 m/min. Determine the following: a) ḿ1 in kg/min b) ῡ1 in m/min
Q1.docx > Q: Find the time required to empty a tank with water height (h=18) 8 ft A 20 ft circular hole
A tank filled with 2125 Liter water emptied within 25 minutes. What is the flow rate in m³/h?
Patrick is building a cabin on a hillside and has proposed the water system shown below. The distribution tank in the cabin maintains a pressure of 27 psig above the water. There is an energy loss of 14.6 lb*ft/lb in the piping. When the pump is delivering 37 gal/min of water, compute the horsepower delivered by the pump to the water. PA = Submit Question Distribution tank 4 ft Flow hp 214 ft Pump 1 ft