Factory X prepares two (2) inductive coils to be used in a drilling operation. It’s goal is to use these two (2) coils to be connected in series as one coil cannot stand to operate alone. The coils when connected across 240 V takes a current separately with values 2 A and 3 A, respectively. When a wattmeter was connected across each coil during the testing, it has indicated 160 W and 500 W, respectively. Calculate for the total power.

Factory X prepares two (2) inductive coils to be used in a drilling operation. It’s goal is to use these two (2) coils to be connected in series as one coil cannot stand to operate alone. The coils when connected across 240 V takes a current separately with values 2 A and 3 A, respectively. When a wattmeter was connected across each coil during the testing, it has indicated 160 W and 500 W, respectively. Calculate for the total power.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 1PA: Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter...

See similar textbooks

Similar questions

Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a switch. The switch is placed in position A at time t = 0 and switched to position B at time t = 743 ms. Find the voltage across each of the resistors at time t = 1.17 seconds. Owo DO A R R in in ete SW éte لفظو
Which of the following would have a greater amount of inductance if connected to an AC power source? a) a coil wound around a wooden core b) a coil wound around a iron core c) they would both be the same d) neither would have any inductance
III. Problem Solving. Compute up to FOUR decimal places. BOX your final answers (with units). 1. What is the equation of the waveform in figure 1? 2. A coil takes 15A from a 250V source. When a 20 Ohm resistor is connected across the coil. The combination draws a total current of 25A. Determine the resistance and inductive reactance of the coil. 3. In the single-phase power system in figure 2, determine the voltage, Vab, and current, I b, being received by the load, 10 +j15 N. V, volts 10 ms AV 100 V Figure 1 250 V 0, deg t, msec CS Scanned with CamScanner j8n 120280°V 12 j3N 252 M €150 121 j45 1 1.250 /150 2.5.2 b Figure 2 j6n j12A
What the voltage falling on the coil in the circuit shown in the figure?
How much resistance must be inserted in series with a 0.96-H inductance to limit the current to 0.25 A from a 120-V 60 Hz power line?
A rotary standard with a KH of 1/3 when per revolution and a multiplier of 3 makes 42.4 revolutions during the testing of a watthour meter with a Kh of 1.8 when per revolution. If the meter has two current coils connected in series makes 48 revolutions, what is percent registration of the meter under test? A. 79.5% B. 102% C. 119% D. 98.1%
Two 115-V incandescent lamps A and B are connected in series across a 230 V source. If lamp A is rated 75 W and lamp B is rated 50 W, determine the current drawn by the series connection.
Three coils each having resistance of 17 Q are connected in star across 415 V, 50 Hz supply. Then the total power consumed is 5849.24 W 595.97 W 718.82 W O 30392.65 W
Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,677 ohms R2 = 1,966 ohms L1 = 3 Henry L2 = 1 Henry Vs = 5 Volts Frequency = 55 Hz What is the Total Impedance (Amplitude) in ohms?
When the voltage source is turned off in a simple circuit consists of a resistor and an inductor, the rate of decrease of the current is proportional to the current. The current is 40 amperes at the moment that the switch is off and dies down to 15 amperes after 0.01 sec. Determine the current in 0.02 sec. 3.375 amperes 4.25 amperes 5.625 amperes 6.025 amperes
Calculate the inductance for a coil with 120 turns, a current of 0.47 mA, and a flux of 1.2x10 Wb. b H a S ww R
A resistor R is connected in parallel with a 10 ohm inductive reactance. The combination is then connected in series with a 4 ohm capacitive reactance. The whole combination is connected across a 100 volt, 60 Hz supply. How much is Rif the angle between the supply voltage and the total current is 45 degrees.