III. Problem Solving. Compute up to FOUR decimal places. BOX your final answers (with units). 1. What is the equation of the waveform in figure 1? 2. A coil takes 15A from a 250V source. When a 20 Ohm resistor is connected across the coil. The combination draws a total current of 25A. Determine the resistance and inductive reactance of the coil. 3. In the single-phase power system in figure 2, determine the voltage, Vab, and current, I-b, being received by the load, 10+j15 N. 250 V V, volts 10 ms A 100 V Figure 1 0, deg t, msec j8n 120280°V 1.2 j3n 252 j4Ω /1.250 150 15.0 2.5.2 Figure 2 j6n j12A

III. Problem Solving. Compute up to FOUR decimal places. BOX your final answers (with units). 1. What is the equation of the waveform in figure 1? 2. A coil takes 15A from a 250V source. When a 20 Ohm resistor is connected across the coil. The combination draws a total current of 25A. Determine the resistance and inductive reactance of the coil. 3. In the single-phase power system in figure 2, determine the voltage, Vab, and current, I-b, being received by the load, 10+j15 N. 250 V V, volts 10 ms A 100 V Figure 1 0, deg t, msec j8n 120280°V 1.2 j3n 252 j4Ω /1.250 150 15.0 2.5.2 Figure 2 j6n j12A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
A non polarized capacitor is connected in DC circuit. Is there a danger of damaging the capacitor when the power turned on?
A sinusoidal voltage with effective value (73 V), and a Frequency its value (80 Hz), was applied on a series circuit that consists of a coil with inductance of value (0.05 H), and a resistor of value (5 N). Calculate: 1. The maximum value of the voltage? 2. The inductive reactance of the coil? 3. The electric impedance of the circuit? 4. The maximum value of the generated current in the circuit? 5. The phase angle? 6. The power factor? 7. The power dissipated inside the coil? 8. Draw a diagram showing the results?
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
The current through a 15kohm resistor is given below, using Ohm’s Law to find the voltage, convert to polar form, complete the math, then convert back to the waveform at i1 = 3.5sin(2500t) mA and i2 = 2.3sin(200t – 60°) mA
Question 2: With the help of mathematical expression and wave forms prove the following. a. V and I are in the phase in purely are circuit. b. V leads I in purely inductive circuit. c. I leads V in purely capacitive circuits.
Draw a graph of current against time for two complete cycles of alternating current of peak value2 A and frequency 10 Hz. Label the axes and indicate correct scale of values on them.(Hin: youhave to calculate the time for one cycle in order to mark the x-axis)
Draw roughly the arc characteristics in alternating currents with a frequency of 50 Hz and 500 Hz, explain briefly
17. The voltage rating of a capacitor .rin Industy beonuse it hes - a. should never be exceeded b. is a minimum working voltage c. is only a suggested maximum d. can be exceeded as long as the time is under one hour
A sinusoidal voltage with effective value (73 V), and a Frequency its value (80 Hz), was applied on a series circuit that consists of a coil with inductance of value (0.05 H), and a resistor of value (5 Q). Calculate: 1. The maximum value of the voltage? 2. The inductive reactance of the coil? 3. The electric impedance of the circuit? 4. The maximum value of the generated current in the circuit? 5. The phase angle? 6. The power factor? 7. The power dissipated inside the coil? 8. Draw a diagram showing the results?
Question 4 a) B M Figure 4 Figure 4 shows the graph of the ripple current. Answer the following i. Describe the function of A. ii. iii. Describe the function of B. Identify the ideal paramater to get the good power supply.