calculate applied pressure for expansion volume of inert nitrogen gas if the change of volume 20 cm³ to 30 cm³ and change of heat at 25C° to 100C° if the work down is zero and heat capacity is 45 J/ K.mol?

Q: pressure in the smaller pipe are provided. Determine the pressure after the expansion including the…

A: For pipe 1 Diameter D1 = 8cm = 0.08 m Velocity V1 = 10 m/s Pressure P1 = 410 kPa For pipe 2 Diameter…

Q: Which of the following whose values are  not depend on the transition of a system from the initial…

A: State functions are those functions whose values are not dependent on the transition path of the…

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: By what factor will the root mean square speeds changed if O₂ is heated from 425 K to 623 K?

A: Urms = 3RTM where R is the gas constant T is temp and M is the molar mass For oxygen, both R and T…

Q: Hot oil at a flow rate of 7.2 kg/s (average c, = 1.92 kJ/kgK) enters an existing counter-flow one to…

A: Given:  Inlet hot oil Temperature = T1 = 385 K  Inlet water Temperature = T3 = 295 K  Outlet water…

Q: Given: Plate thickness: 30 mm k = 45 W/m°C Uniform volumetric heat generation: q, = 25 MW/m3…

A: i) Let A be the cross-sectional area perpendicular to the direction of heat flow S (W/m3) is the…

Q: 4. Compute the thermal conductivities of NO and CH at 300K and atmospheric pressure from the…

A: Hi and thanks for the question. Since you have posted multiple questions and didn't specify which…

Q: Write a process path for the heating and compressing of nitrogen. Include the state of the coumpound…

A: Given, Initial temperature, T1 = 293.15 K Initial pressure, P1 = 2×105 Pa Let the moles of the gas…

Q: It is proposed to condense 15 pounds per sec of saturated Freon-12 vapor in refrigeration system by…

A: Given:- Mass flow rate m=15 lb/sOutter dia meter Do= 1 inch =0.0833 ftInlet Temperature = 70∘FOutlet…

Q: <p A horizontal tube-bundle air-cooled exchanger is used to condense steam at 250 F and has the…

A: I'll answer each question step-by-step, using the given information from the image.1. What is the…

Q: In the case of determining heat rates and fluxes, is power required for the system the same as the…

A: Heat rate: Heat rate is defined as amount of heat (energy) per unit time. Unit of energy may be…

Q: Calculate the rate of heat transfer for a steam flow rate of 220 Kg/Sec and latent heat of…

A: Given that, The mass flow rate of steam ms = 220 kgs The latent heat of vaporization λs = 25 kJkg It…

Q: The compression ratio of an air-standard dual cycle is 12, and the pressure at the beginning of…

A:

Q: How many heat are needed to change 50 kg of ice at -10.0 °C to steam at 250 °C?

A: Given: m  = 50 kg Ti = -10.0 °C (Ice) Tf = 250 °C (Steam)

Q: I understand that we have to use this formula Heat current=(k. Area. change in temperature)/length…

A: Firstly, the brass rod one end is in boiling water, which means this rod is hot. While the Copper…

Q: How much heat in kJ must be transferred to 10 kg of air to increase the temperature from 100C to…

A: From first law of thermodynamics, dU=dq-dw, Now dw=PdV, dU+PdV+VdP=dQ, As dP =0,

Q: A pipe (ID: 130 mm, OD: 165 mm, k=15 W/m²-K, Length: 2 meters)is insulated with several materials,…

A: Given Pipe Di=130mm D0=165mm K=15 W/(m2K) L=2m Inside fluid –Oil temperature T1=118℃ Insulation is…

Q: 2.6 A cylinder 10 m high, with a cross-sectional area of 0.1 m², has a mass-less piston at the…

A:

Q: How many heat are needed to change 50.0 grams of ice at -15.0 °C to steam at 120.0 °C?

A: Given: mass of ice = 50g=50g×kg1000g=0.05kg temperature of ice = -15°C=-15+273K=258K temperature of…

Q: A piston-cylinder device initially contains gas at 200 kPa. The system showed an expansion due to…

A:

Q: At the initial state, the pressure and temperature of water vapor in the metal tank were 20 MPa, 520…

A: Initial temperature of water vapor, T1 = 520ºC = 793.15 K Initial pressure of water vapor, P1 = 20…

Q: 7.1 What is condenser ? 7.2 What are the functions of a condenser in a thermal power plant? Give the…

A: A condenser is an essential component in thermal power plants, converting exhaust steam back into…

Q: (For Nos 4 to 6). Heat Loss from a Pipe. A bare stainless steel tube having an outside diameter of…

A: Given Data: Outside diameter; D=76.2 mmD=0.0762 m Emissivity; ε=0.55 Temperature; T1=366.4 KT2=294.2…

Q: Find the two-dimensional temperature distribution T(tz) under steady state condition. Where, To-20…

A: T0 = 20 C = 293 K T(L) = 1000 C = 1273 K Density (p) = 800 kg/m^3 k = 200 W / m K Cp = 2500 J/ kg K…

Q: A sealed constant-volume container has 0.8 kg of liquid water and 0.2 kg of water vapor at 0.10 MPa…

A:

Q: A piston-cylinder assembly has 1 kg of air at 700 kPa and 400C. The piston cross-sectional area is…

A: This problem is based on the concept of ideal gas law. The data given : Initial temperature ,T1 =…

Q: Consider 2 kg of air has a decrease of internal energy of 25 kJ during a reversible non flow…

A:

Q: Find the volume of nitrogen gas when change heat at temperature 20 Co to 50 Coif that gas container…

A: Given data:  Initial temperature = 20 0C Final temperature = 50 0C

Q: Q.3 Two Infinite Black plates at 1800k and 180C² exchange = heat by radiation calculate heat…

A: Given that- Two infinite black plates are at, temperatures T1=1800 K T2=1800C= 453 K The diagram can…

Q: Q. For case 3(The end of the fin is insulated). Prove that fin efficiency is equal to VHPKA 0 tanh…

A: All the abberivations used have there general meaning. The detailed solution is aattached below.

Q: Determine the amount of heat needed to vaporize 26.7 g of water at 100C

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: (2) Calculate the Fanning Friction Factor (f) using the formula: = 2.5 In Re, +1.75 8

A: Given, Equation for fanning friction factor is 1f = 2.5lnRef8+1.75    .....1   Here, Reynolds…

Q: A 3 meter tall aluminum tank with a 7 meter diameter is completely filled with ethanol. The empty…

A: An aluminum tank consist of ethanol at 25 0C.

Q: Steam in a heating system flows through a 1-m long tube whose outer diameter is D1 = 3 cm andwhose…

A: Given: diameter D1 = 3 cm = 0.03 m Radius r1 = 1.5 cm = 0.015 m Circular fins (k = 46 W/m. °C) of…

Q: Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C.…

A:

Q: Prove that the dimensionless temperature through the Plane wall with heat generator is: T(X) - T(S)…

A: we need to determine the dimensionless temperature distribution in plane wall and prove the given…

Q: Water is poured into an insulating container. The water has mass m, = 1.2 kg and an initial…

A: Equilibrium temperature for the system is to be calculated.

Q: 5) One mol of air at 0.5 MPa and 400 K, initially undergoes following processes, sequentially: a)…

A: