cab AB carries a tension of 500 N. Determi clockwise) of this tension as applied to point A of 650 mm B Answer: Mo= 32 i 350 mm A N
Q: 0.5 in. 0.55 in. 1 0.25 in. P PI 3.5 in. A "В B 1.6 in. O C D 0.65 in. 0.75 in. E Knowing that…
A: Given data A vertical force F=380 lbDistance AB=0.65 inDistance BD=0.75 inDistance CE=1.6 inWe are…
Q: A circular rod of cross-sectional area 2 x 104m² has a tensile force of 80 kN app The stress in the…
A:
Q: A picture frame is hung using a rope 3 mm in diameter. The maximum stress in the rope is not to…
A: To solve this problem we use equilibrium for frame. Stress in this case is given by:…
Q: 5. The drill pipe shown in the figure below is designed as a hollow shaft with an outer diameter of…
A: A.Step 1:Given Parameters:Outside diameter : D = 80 mm= 0.08 m Inner diameter: d = 70 mm = 0.07…
Q: TUnOWng prUDIEms. A steel wire of diameter 1 mm can support a tension of 0.2 kN. Determine the…
A:
Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…
A:
Q: The radius of the brass rod is 3 mm. What force will stretch it by 0.25% of its length. Ebrass = 9…
A: Given: Ebrass = 9 x1010 The radius of the brass rod r = 3 mm To determine: Force require to…
Q: Please help me with this solution.
A: In the given, we can find the ultimate shearing stress of the shear pin by:First, we calculate the…
Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…
A: Have a look
Q: 1. In the system shown, cable A has an Ultimate Stress of 201 MN/m². For this application the cable…
A:
Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…
A:
Q: The homogeneous wire ABCD is bent as shown and is attach to a hinge at C. Determine the length L…
A: this question is about to measure center of gravity of wire for equilibrium.
Q: I need only last question question number 20 .
A: Approach to solving the question:Please see attached photos for detailed solutions. Thank you.…
Q: 2. For safety in climbing, a mountaineer uses a nylon rope that is 58 m long and 1.2 cm in diameter.…
A: Given that: The length of the rope is L=58 m The radius of the rope is d=r2r=1.22=0.6 cmr=0.006 m…
Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…
A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…
Q: A steel wire of diameter 1 mm can support a tension of 0.2 kN. Determine the diameter of a steel…
A:
Q: A steel bar is 10 mm in diameter and 2 m long. It is stretched with a force of 20 kN. Calculate the…
A: Given data: Diameter (d) = 10 mm = 0.010 m Length = 2 m Force (F) = 20 kN = 20 × 103 N Required: The…
Q: A 50 kg girl wearing high heel shoes balances on a single heel of diameter 1.0 cm. Calcula the…
A: Given that,Mass of the girl : (m) = 50 kg Acceleration due to gravity : (g)=9.8 m/s2Diameter of the…
Q: Part 1. A force stretches a (first) wire by 2mm. This wire is made of an unknown material and has a…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: 3. Using the Method of Sections determine the load in members BD, CD, and CE.
A:
Q: Two rods are identical, except that one is brass (Y = 9.0 × 1010 N/m²) and one is tungsten (Y= 3.6 x…
A:
Q: A cylinder with a bore diameter of 4.5 inches and a rod diameter of 1.5 inches is to be used in a…
A: Given: The bore diameter of the cylinder is 4.5 inches. The rod diameter is 1.5 inches. The force…
Q: what is the percentage elongation of an elastic with a cross section of 5 cm2 If the force of 15 N…
A: Given- area of cross-sectional of elastic , A = 5 cm2 = 5 x 10-4 m2 applied force , F =15 N Young's…
Q: Q2: A conveyor beam has the cross section shown below and it is subjected to a be moment. Determine…
A: Solution:- Given data; Area (1) =25×150=3750 mm2…
Q: For safety in climbing, a mountaineer uses a nylon rope that is 65 m long and 1.3 cm in diameter.…
A:
Q: 2. A tall building with a cross-section A, a mass M and a Young's modulus Y has a height L on Earth.…
A: The mass of the building is M Area of cross section is A Young's modulus Y Height of the building is…
Q: E Q5: A torque of 5 N.m is required to rotate the intermediate cylinder at 40 r/min. Čalculate the…
A: Consider the given data as below. Torque, τ=5 N·m Length of all cylinder, L=500 mm=0.5 m Angular…
Q: ) For the structure shown, determine the internal loadings acting on the cross-section at point B.…
A:
Q: Choose the correct answer. Surface tension of Dates Syrup is more than that of water O True O False…
A: Viscosity of dates syrup is more than that of water. Comparison of surface tension for dates syrup…
Q: 200 kN 0 -400 mm 200 kN
A:
Q: Determine the force P required to maintain the 225-kg engine in the position for which 0=35°. The…
A:
Q: If the mass of tbe cylinder is 40kg,determine the mass of cylinder A, M(A), in order to hold the…
A: Mass of cylinder C, m1= 40 kg Angle (DEB) = 180° - 30° = 150° tension in EB(T1) = Tension in BC =…
Q: A hydrocarbon oil of specific gravity 1.15 flows through a schedule 40 carbon steel pipe at a rate…
A: This question is based on energy.
Q: A tensile load of 45 kN is applied to 15 mm diameter bar. Calculate the engineering stress on the…
A: Data Given , Tensile load ( P ) = 45 KN = 45×103 N Bar diameter ( d ) = 15 mm = 15 × 10-3 m…
Q: A cable used to lift heavy materials can resist breaking even under a load of 1 meganewtons. The…
A:
Q: For safety in climbing, a mountaineer uses a nylon rope that is 65 m long and 1.4 cm in diameter.…
A:
Q: beyond the maximu Fter some time?
A: Given: What happens when the stress applied to the body is increased beyond the maximum value and is…
Q: In air, a gymnast holding on to a pair of gymnastic rings with straps tied to mounts which are…
A: In order for the gymnast to maintain static equilibrium while holding on to the gymnastic rings, the…
Q: Determine the force P required to maintain the 210-kg engine in the position for which = 20°. The…
A:
Q: The dimensions of the Tensile Stress is Select one: O a. MLT-1 O b. ML2T-2 O c. MLT-2 O d. ML-1T-2 O…
A:
Q: H horizontal force of P = 1,400 lb is applied to the rectangular bar shown in Figure above. d = 1.80…
A:
Q: A cast iron rod of diameter 18 mm and length of 240 mm is subjected to a tensile load of 100 kN, and…
A: Given. T = 100KN = 100,000 N D = 18mm = 0.018 m L = 240mm = 0.24m ∆L = 0.0006 m
Step by step
Solved in 2 steps with 1 images
