C8. A simply supported beam spans 22 feet, with b = 14" and h = 28". It carries a uniform Live Load of 2.50 kips fA. and a uniform Dead Load of 1.25 kips/ft. which includes the weight of the beam. "Assume the clear cover is 1.5 inches and a #3 stirrup will be used. CS. Calculate: a) My b) The number and size of bars needed c) The actual value of "d" d) ¢M, – is the beam adequate? f.'= 3,000 psi, fy = 60 ksi

C8. A simply supported beam spans 22 feet, with b = 14" and h = 28". It carries a uniform Live Load of 2.50 kips fA. and a uniform Dead Load of 1.25 kips/ft. which includes the weight of the beam. "Assume the clear cover is 1.5 inches and a #3 stirrup will be used. CS. Calculate: a) My b) The number and size of bars needed c) The actual value of "d" d) ¢M, – is the beam adequate? f.'= 3,000 psi, fy = 60 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the co-ordinates for (Pnb, Mnb) and (Pub, Mub) for rectangular columns using h=24in b=14in Effective cover =3in. Reinforcement consists of 4-#9 bars on each side (totla of 8 bars) f'c=7000 psi fy=40000 psi. Use a yield strain of 0.004 for steel.
A propped cantilever beam ABC (see figure) has a shear release just right of the mid-span. P = qL C A B Shear release- L L/2 L/2 – (a) Select the most economical wood beam from the table in Appendix G; assumeq = 55 Ib/ft, L = 16 ft, o = 1,750 psi, and t = 375 psi. Include the self-weight of the beam in your design. (Enter the nominal dimensions in inches.) in. x in. (b) If a C 10 x 25 steel beam is now used for beam ABC, what is the maximum permissible value of load variable q (in Ib/ft)? Assume o, = 21 ksi and L = 10.5 ft. Include the self-weight of the beam in your analysis. (Use the section modulus for axis 2-2.) as Ib/ft
H.W Draw S.f,B.M and elastic dliagrams for the beam Shown below by method of equntions ? 6W/m 20 KN 6m 2m 2m
Draw SFD and BMD for the cantilever beam subjectedto loading as shown below. 40KN 0.5m 300 20KN/m 0.7m A IPAL MAN 1m 1m Indpired by life
Design a square base plate to support 10 mm thick pipe column with an inside diameter of 300 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 850 kN and PLL =420 kN. Assume that the pipe is to rest on a very wide slab. Use A-50 steel and concrete fc’ = 35MPa and LRFD.
In a given T-Beam, flange width = 700 mm, slab thickness = 100 mm, web thickness = 350 mm, effective depth = 450 mm. It is singly reinforced at the bottom side (tension side) with As = 2775 sq. mm. Take fc' = 17.24 MPa, fy = 413.7 mm. a) Determine the value of compression block "a"
The following is a cross-section of a tied column reinforced with 16-32 mmø. Using fc' = 28 MPa and fy = 415 MPa. Size of aggregates used is 25 mm. O Computè the safe ultimate load that the column could carry. ® Compute the spacing of the 10 mm wires. 3 . Compute the min. clear cover over the tie wire. O Compute the clear spacing between longitudinal bars. -600 600
1. A rectangular beam has b = 300mm, d = 500mm, As = 6 – 32mm diameter bars, fc' = 27.6 MPa, fy = 414 MPa. Calculate: a) depth of compression block, "a" b) fs c) + d) Mu
Solve it
Draw the shear diagram for the following beam
E/Y Q4. Select the diameters of the ties AB and CD (see figure) if the load P is 10 t, and the allowable stress [σ] for the material of the ties is 1000 kg/cm2. Answer: CIAB - 424 mm; dc0 = 25.2 mm P 1m 1 B D -im- -Im- im