C4.4 The cantilever beam AB of length L carries a distributed loading w that varies with the distance x. Given L and w(x), construct an algorithm to plot the shear force and bending moment diagrams. Use (a) L=3 m and w= (50 kN/m) sin(r.x/2L); and (b) L = 5 m and 20 kN/m if x < 1.0 m (20 kN/m)· 1.0 m if 1.0 m < x <4 m w = if x> 4 m|

C4.4 The cantilever beam AB of length L carries a distributed loading w that varies with the distance x. Given L and w(x), construct an algorithm to plot the shear force and bending moment diagrams. Use (a) L=3 m and w= (50 kN/m) sin(r.x/2L); and (b) L = 5 m and 20 kN/m if x < 1.0 m (20 kN/m)· 1.0 m if 1.0 m < x <4 m w = if x> 4 m|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 504N, 1) The value of horizontal resultant R is: E A D 853.814N + O 796.894N → O 711.512N - O 640.361N → O None of these
please answer it with ; given, solution, diagrams/ drawing, answer please expain part by part
using MATLAB
4.2 Please show your complete solution.
Of a column of infinite length to points A, B, C and D parallel FA, FB, FC and FD (kN) respectively Using the forces in the directions given in the figure, equivalent resultant force (FEŞ) size and application x and y (m) coordinates of the point find. FA=20 FB=55 FC=35 FD=77 xA=13 yA=8 xB=3 yB=5 xC=10 yC=0 xD=-9 yD=-15
Draw the shear and moment diagrams for the figure shown Show your solutions 80KN 40KN ▼ 30 KN/m v 3m 3m 3m
Q5. The beam AB is pinned at A and lifted by a rope and pulley system to support a distributed load of 200 N/m. T= 1500 N, Ax =1500N, Ay= 300N] (a) Calculate the rope tension and the support reaction at A. (b) Draw the shear force and bending moment diagram for beam AB (c) Determine maximum bending stress and shear stress. (d) Use Macaulay function to derive the slope and deflection equations. Determine the maximum deflection in beam AB. [-50.83 MPa, 500 kPa] T 0.1 m 0.5 m 30mm B. 60 mm 200 N/m cross section 0.75 m 2.25 m
ANSER FAST
A uniform aluminum beam 9.00 m long, weighing 300 N,rests symmetrically on two supports 5.00 m apart (Fig. ). A boyweighing 600 N starts at point A and walks toward the right. (a) In thesame diagram construct two graphs showing the upward forces FA andFB exerted on the beam at points A and B, as functions of the coordinatex of the boy. Let 1 cm = 100 N vertically and 1 cm = 1.00 m horizontally.(b) From your diagram, how far beyond point B can the boy walkbefore the beam tips? (c) How far from the right end of the beam shouldsupport B be placed so that the boy can walk just to the end of the beamwithout causing it to tip?
When a beam section is subjected to a shear load, a shear stress distribution is developed on the section. The distribution of the shear stress is not linear. Elasticity theory can be used to calculate the shear stress at any point. However, a simpler method can be used to calculate the average shear stress across the width of the section, a distance y above or below the neutral axis. The average VQ shear stress is given by T = Here V is the shear It force on the section, I is the moment of inertia of the entire section about the neutral axis, and t is the width of the section at the distance y where the shear stress is being calculated. Q is the product of the area of the section above (or below) y and the distance from the neutral axis to the centroid of that area (Figure 1). In short, Q is the moment of the area about the neutral axis. I Figure 1 of 1 An I-beam has a flange width b = 250 mm, height h = 250 mm, web thickness tw = 9 mm, and flange thickness tf = 14 mm. Use the…
a) Let's start with a simplified model where both M, and M₂ are applied perpendicular to the moment arm. The moment arm lengths are d₁ = 3 cm, d₂ 15 cm, and d3 = 34 cm. M₁ M₂ da W Calculate the ratio of the mechanical advantage of the brachioradialis(M₂) to the mechanical advantage of the biceps(M₁). Ratio of Mechanical Advantage MA2 -) = 5 MA1