c2 (). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. 2 : (ii) A 16 kVA, 56HZ, single-phase transformer has a turns ratio of 16:2 and is supplied from a 3 kV supply. Neglecting losses, determine (a) the secondary voltage. (b) the full load primary current, (c) the maximum flux and (d) the minimum value of loa resistance which can be connected across the secondary winding without the kVA rating being exceeded. 4 a: xan secondary voltage primary current maximum flux secondary resistance

c2 (). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. 2 : (ii) A 16 kVA, 56HZ, single-phase transformer has a turns ratio of 16:2 and is supplied from a 3 kV supply. Neglecting losses, determine (a) the secondary voltage. (b) the full load primary current, (c) the maximum flux and (d) the minimum value of loa resistance which can be connected across the secondary winding without the kVA rating being exceeded. 4 a: xan secondary voltage primary current maximum flux secondary resistance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase transformer has 180 and 45 turns, respectively, on its primary and secondary windings. The corresponding resistances are 0.2422 and 0.076 S2, respectively. Determine the equivalent resistance a. in primary terms, and b. in secondary terms.
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
None
.
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. (ii) A 12 kVA, 56HZ, single-phase transformer has a turns ratio of 18 : 2 and is supplied from a 2.5 kV supply. Neglecting losses, determine (a) the secondary voltage, (b) the full load primary current, (c) the maximum flux and (d) the minimum value of load resistance which can be connected across the secondary winding without the kVA rating being exceeded secondary voltage primary current maximum flux secondary resistance
B/ Fill in the blanks: 1. The purpose of providing the iron core in the transformer is to 2. A transformer transforms... 3. Power transformers are designed to have maximum efficiency at 4. The transformer ratings are usually expressed in terms of menm
In no load phasor diagram of practical transformer, the magnetizing current is with flux 4. In phase 90 Degree out of phase Lagging by 60 Degrees Leading by 60 Degrees
The voltage per winding of the 220V/12V, 50 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm2 ?
High voltage engineering
A 3.5 kV / 120V, 50 Hz, single phase transformer is to have an approximate e.m.f per turn of 33V and operate with a maximum flux density of 1.35T. Determine, (a) The number of primary and secondary turns. (b) The cross sectional area of the core.
In a practical transformer, Identify, which component of no load current supplies eddy current loss? a. I0 b. IC c. IM d. None of these
Choose the correct answer from the given alternative: 1. In an ideal transformer, (a) windings have no resistance (c) core has no losses (b) core has infinite permeability (d) all of the above. 2. The primary and secondary induced e.m.fs. El and E2 in a two-winding transformer are always: (a) equal in magnitude (b) in-phase with each other (c) antiphase with each other (d) determined by load on transformer secondary. 3. In relation to a transformer, the ratio 20: 1 indicates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 4. A transformer has negative voltage regulation when its load power factor is: (a) zero (b) lagging. (d) unity (c) leading 5. During short-circuit test, the iron loss of a transformer is negligible because: (a) the entire input is just sufficient to meet Cu losses only…