C1 (a). A lubricating oil having the dynamicviscosity of 0.058 poise and kinematic viscosity of0.14 stokes. Calculate (i) the density of oil inkg/m3, (ii) the weight density of oil in N/m3, (i) thespecific gravity, and (iv) the specific volume inm3/kg.C1 (b). Calculate the capillary effect in mm in aglass tube of 3.6 mm diameter, when immersed in(1) water (2) mercury. The values of surfacetension in contact with air are 0.0743 N/m and 0.75N/m respectively. The contact angle for water =0°and mercury =130°.C1(a).(i).The density of oil in kg/m3C1(a). (ii) the weight density of oil in N/m3C1(a). (iii) the specific gravityC1(a). (iv) the specific volume in m3/kgC1 (b). 1.The capillary effect (water) in mmC1 (b). 2.The capillary effect (mercury) in mm

Given Kinematic viscosity = 0.14 × 10-4 m2 / s Dynamic viscosity = 0.0058 Ns / m2

C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of 0.14 stokes. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (i) the specific gravity, and (iv) the specific volume in m3/kg.

C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of 0.14 stokes. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (i) the specific gravity, and (iv) the specific volume in m3/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is approximately the same across the species. The values of viscosity were 0.0035 Ns/m² for the human and 0.0040 Ns/m² for the rabbit. The diameter of the aorta is 2.0 cm for the man, and 0.7 cm for the rabbit, estimate the heart rate beats per minute (bpm) for both species
What is the principle involved in measuring Kinematic and Dynamic viscosity of oil using Saybolt viscosity? How is falling of sphere method differ from Saybolt Universal viscosimeter?
A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
The most influencing parameter on Reynold number is: choose one 1-Fluid density 2-Fluid velocity 3-Fluid viscosity 4-None of above
An airplane that has a cross-sectional diameter D = 4 m of the front portion is to fly at a speed of 600 km/hr in air that has a density of 1.1 kg/m and dynamic viscosity of 1.27 x 10 Pa.s. A small size model of scale ratio (1/17) to be tested in a different fluid that has a dynamic viscosity 5 x 105 Pa .s and a density of 500 kg/m2. It is determined that the parameters that are important for this test are: diameter D, density, viscosity, velocity V, the length of the wings L and the drag force F. What must be the speed (m/s) of the model to Choose... ensure dynamical similitude? What must be the corresponding diameter of the model (cm)? Choose.. What is the number/s of dimensionless groups for this problem? Choose...
5. The bulk modulus of compression......... (a) is independent of temperature of pressure and viscosity (b) increases with the pressure (c) is independent (d) has a dimensionless unit 6. If a non-uniform solid body weighs 500 N in air and when it is completely submerged in water its weighs is 300 N. If it has a volume of 0.0136 m³ then its specific gravity is.......... (c) 2.5 (d) 3.0 (e) none of these (a) 1.5 (b) 1.7 7. A flat plate of area 1.5 m² is pulled with a speed of 0.4 m/s relative to another plate with a distance of 0.15 mm clearance between them. For a fluid viscosity of 0.1 Pa.s, the power required to maintain this speed is (a) 160 W (b) 100 W (c) 200 W (d) 400 W 8. A solid wooden cylinder (SG = 0.6) has diameter of 0.8 m and a height of 3 m, when the cylinder is floating vertically on its base in water then the submerged height of the cylinder is. (a) 1.1 m (b) 1.4 m (c) 1.8 m (d) 2.6 m 9. A wooden cube (SG=0.6), its base 5 cm x 5 cm and has 10 m height, floats vertically…
The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.50. Compute the equivalent kinematic viscosity in m2/s (decimal form)
Directions: Solve the following problems completely, and make a detailed solution. Any incompletesolution arriving at such answers will never be considered. A barrel contains a 15 cm layer of oil of density 5.88 kN/m3 floating on water that is 30 cm deep. What is the gauge pressure in mmHg at the oil-water interface?
Question 2: The pressure drop, AP, in a horizontal pipe depends on the pipe diameter, d, pipe length, L, pipe roughness, ɛ, average velocity, V, density of the fluid, p, and absolute viscosity of the fluid, u. Express the variables in non-dimensional form using Buckhingham-Pi theorem
1.32 A 1.5 in diameter shaft rotates in a sleeve bearing which is 2.5 in long. The radial clearance between (he shaft and the slecve is 0.0015 in, and this is filled with oil having , = 1.$3 x 10-2 lb/ft•s Assuming rotational speed of 62 rpm and a lincar velocity gradient in the lubricating oil, determine the resistive torque due to viscous shear at the shaft-lubricant interface. Ans. 0.0079 ft-lb
36. Aspherical tank of 1.2 m radius is half-filled with oil of relative density 0.8. If the tank is given a horizontal acceleration of 10 m/s, calculate: (i) The inclination of the oil surface to horizon- tal. (ii) The maximum pressure on the tank. [Ans. (i) 45.55°; (ii) 9.4 kN/m²]
C1 (a). A lubricating oil having the dynamic viscosity of 0.051 poise and specific gravity of 1.12. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. (