(c) You have been tasked as an engineer working with the Coca-Cola plant todesign an inverting amplifier circuit to amplify input signal of 10mV from a sensorcircuit that monitors the bottling operation. The amplifier circuit is to drive a load(an alarm) of 2k2. To drive the load, the amplifier circuit must have a closed loopgain of 60 dB and an input resistance of 5k2. Draw the circuit diagram and findthe design parameters of the circuit. Find the input current to the amplifier circuit,the output voltage required to drive the load, and the load current.

According to the given statement, We can draw the inverting amplifier circuit as

(c) You have been tasked as an engineer working with the Coca-Cola plant to design an inverting amplifier circuit to amplify input signal of 10mV from a sensor circuit that monitors the bottling operation. The amplifier circuit is to drive a load (an alarm) of 2kN. To drive the load, the amplifier circuit must have a closed loop gain of 60 dB and an input resistance of 5k2. Draw the circuit diagram and find the design parameters of the circuit. Find the input current to the amplifier circuit, the output voltage required tio drive the load, and the load current.

(c) You have been tasked as an engineer working with the Coca-Cola plant to design an inverting amplifier circuit to amplify input signal of 10mV from a sensor circuit that monitors the bottling operation. The amplifier circuit is to drive a load (an alarm) of 2kN. To drive the load, the amplifier circuit must have a closed loop gain of 60 dB and an input resistance of 5k2. Draw the circuit diagram and find the design parameters of the circuit. Find the input current to the amplifier circuit, the output voltage required tio drive the load, and the load current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Advantages of Inverting and Non-inverting Op Amp
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
8. If the CMRR of a practical op-amp is 108 dB and the common mode gain is 0.4, the open loop gain is: a) 100000 b) 200000 c) 400000 d) 500000
Figure 3 shows a Hartley oscillator. Assume that the op-amp employed in the figure is an ideal op-amp, and R1= 20 kΩ, R2 = 60 kΩ, L1=10 mH. b) State the Barkhausen criterion for sustained oscillation.c) Explain briefly how the phase shift requirement for sustained oscillation ismet in the circuit of Figure 3.d) The feedback ratio and oscillation frequency of Figure 3 are givenrespectively by, B = -L2/L1 and w0 = 1 / sqrt(L1 +L2)C Determine the values of C and L2 in order for the circuit to oscillate at a frequency of 200 Hz.
Drive the following equation Vo=-11 Vin. Using summing amplifier RI circuit.
File Edit View For an operational amplifier, the common mode gain is 0.1 and the differential gain is 1000. What will be the CMRR of the opamp?
If in the oscillator block diagram shown in Figure, = 0.1V, A = 100 and m = 0.01, then the circuit will. V₁ mVo Voltage Gain A Feedback Circuit V
These questions from electronics lab course, from The common Collector Amplifier (Emitter-Follower) Experiment.
(a) An instrumentation system shown in Figure Q3 (a-i) has a Nickel resistor detector device (RTD) sensor with the characteristics shown Figure Q3 (a-ii). The three wires bridge has R1= 200 Q, R2= 500 Q, and R3= 650 Q. The amplifier has a gain of 17.2, and the battery voltage is VB=1.2v. (i) Calculate the amplifier output voltage Vo when the boiler temperature is 150 °C. (ii) Explain the RTD principle of operation. R1 R2 Industrial boiler Nickel R3 RTD Vaa Vo Figure Q3 (a-i) 400 Nickel 350 300 Platinum 250 200 150 100 50 Copper -200 200 400 600 800 RTD temperature (oC) Figure Q3 (a-i) RTD Resistance ()
2) Discuss howthe followingAnalog to Digitalconversion is done using Op-amps(any three):i)integratingtype,ii)successive approximationtype,iii)flash converters ,iv)sigma and delta converters.