c) Show that the transfer function can be put în the form X,(s) X: (s) ¯ Za + Z1 where Z, and Zz are Z, = b2s, 2 = b,s + k. d) Using the result of part (e), draw a schematic diagram of an analogous electrical system and denote explicitly the relations between the analogous electrical system parameters with the original mechanical system parameters. [Hint: Remember that the transfer function of the electrical system: E, (s) E, (s) – Z,+ Z,' and you may use this fact to construct the analogous electrical system. In addition, remember that the complex impedances for a resistor with resistance R and a capacitor with capacitance C are Z = R and Z = respectively. If you need further hint, solve the next problem.] %3D

c) Show that the transfer function can be put în the form X,(s) X: (s) ¯ Za + Z1 where Z, and Zz are Z, = b2s, 2 = b,s + k. d) Using the result of part (e), draw a schematic diagram of an analogous electrical system and denote explicitly the relations between the analogous electrical system parameters with the original mechanical system parameters. [Hint: Remember that the transfer function of the electrical system: E, (s) E, (s) – Z,+ Z,' and you may use this fact to construct the analogous electrical system. In addition, remember that the complex impedances for a resistor with resistance R and a capacitor with capacitance C are Z = R and Z = respectively. If you need further hint, solve the next problem.] %3D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.8MCQ: The units of admittance, conductance, and susceptance are siemens. (a) True (b) False

See similar textbooks

Similar questions

If the values of real power and reactive power is specified for a bus, then it is called as PV bus. Select one: True False
The cost of in ... .... .... HVDC transmission is higher compared to the substation in HVAC transmission. O transmission line O transformer O converter station O conductors
Using the first method shown in the image, draw the circuit that would solve for V_l (voltage) and I_l (current). Compute all referred values and label all components.
Fundamentals of Electrical Engineering 2020/2021 Dr. Yaseen H. Tahir We can note that IL and Vi are same in both cases. Example: a) Convert the current source of Figure below to an equivalent voltage source. b) Prove your answer. (Home work) Rs 10KQ 20KO 5 mA b.
1. Explain maximum power transfer theorem2. What are some of the instances where power transfer is empluyed in electrical circuits?
The Subject is Basic Electrical Engineering Chapter 6. Network Reduction Network Reduction (Delta-Wye Transformation, Wye to Delta Transformation)
Using nodel
Fundamentals of Electrical Engineering 2020/2021 Dr. Yaseen H. Tahir Eхample: Apply KVL to determine the voltages Vae and Vece. 12 V +16 V - ww R, 24 V R $4V R f 10 V + 6V + Solution: Note: 1. Since points (a and e) as well as (e and c) are not physically close, the arrow notation is very useful. 2. In order to determining the unknown voltage, we must apply KVL in the closed path that consist of the unknown voltage. # Therefore, to determine Vae: a) we can use the path faef as: b) or we can use the path abcdea as: # And to determine Vee: a) we can use the path cdec as: b) or we can use the path cefabc as: c) since Vae is now known, we can also use the path ceabc as: 56
Xa) Given the circuit diagram in Figure 2.31 showing admittances and current sources at nodes 3 and 4, set up the nodal equations in matrix format. (b) If the parameters are given by: Y, =- j0.8 S, Y = -j4.0 S, Y. =-j4.0 S, Ya =-j8.0 S, Y. =-j5.0 S, Yf -j2.5 S, Y =-j0.8 S, I3 = 1.0/-90° A, and I = 0.62/-135° A, set up the nodal equations and suggest how you would go about solving for the voltages at the nodes. Yo Y. Ya Y lell Yo I4 13 O lell ell
Introduction: write about Voltage, Current and Electrical Impedance
"leal Engineering 20 (43) Dr. Yaseen H. Fundamentals of Electrical Engineering 2020/2021 H.W: Find all the nodesvoltages in the networks in Figures below using nodal analysis. branch Curreny a) mA 1 kf2 4 mA c) 2 mA 3 kn3 6000 312 kll 3 12 ktl ww 3 V VANDOD
Q.1. A power suppply having 220 V AC input and two fixed outputs as 10 V DC and 20 V DC is requested from you. For this purpose, a transformer with 220 V AC input / 15 V AC output, some capacitors, some silicon diodes, and zener diodes are presented.a) Design your power supply and point out DC voltage outputs b) Explain the operation of the network and all the components used in the design .c) Calculate and plot input and output signals of the network.Hint: For design, remember clipper, clamper, rectifier,voltage multiplier and zener circuits