Some practice questions for class test(1).pdf - Adobe Acrobat Reader DC (32-bit)FileEditView Sign Window HelpHomeToolsSome practice ques... xUNIVERSITY OF UL..早2 画Q21180%Search 'Crop P(b) For the comparator circuit shown below, a sinusoidal input signal with a peak voltageP Export FEdit PD(Vp) of 5 V and a frequency of 1 Hz is applied to the non-inverting terminal. Assume +VccCreateas +12V and -Vcc as -12 V, with corresponding saturation voltages of +Vsat of +11 V and -CommVsat of -11 V and R1 and R2 values of 100 kM and 50 kN, respectively. Assuming that thei CombEl Orgarsignal frequency is well below the slew rate limit, describe and draw what would be theDelete, insertrotate pages.comparator output.Cor+VccA RecVinPro5 VVNAc+VccVVotoR1R21 s-VccDELLくP.近

Answered: Image /qna-images/answer/708abab6-96cf-4929-82ba-6b2bb0c569f1.jpg

180%- 日2 在會Q 回☆ 6 @ 213 (b) For the comparator circuit shown below, a sinusoidal input signal with a peak voltage (Vp) of 5 V and a frequency of 1 Hz is applied to the non-inverting terminal. Assume +Vcc as +12V and -Vcc as -12 V, with corresponding saturation voltages of +Vsat of +11 V and - Vsat of -11 V and R1 and R2 values of 100 kQ and 50 kN, respectively. Assuming that the signal frequency is well below the slew rate limit, describe and draw what would be the comparator output. +Vcc Vin 5 V VN + +Vcc I Vo R1 R2 1 s Vcc

180%- 日2 在會Q 回☆ 6 @ 213 (b) For the comparator circuit shown below, a sinusoidal input signal with a peak voltage (Vp) of 5 V and a frequency of 1 Hz is applied to the non-inverting terminal. Assume +Vcc as +12V and -Vcc as -12 V, with corresponding saturation voltages of +Vsat of +11 V and - Vsat of -11 V and R1 and R2 values of 100 kQ and 50 kN, respectively. Assuming that the signal frequency is well below the slew rate limit, describe and draw what would be the comparator output. +Vcc Vin 5 V VN + +Vcc I Vo R1 R2 1 s Vcc

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write about two applications for a series circuit, (Think about the different electronics at home or at work), and some of the advantages and disadvantages?
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
1-) With a +5 V (dc) common mode signal at the input of the circuit in the figure. There is a difference signal in the form of Vdiff = VI1-VI2 = 10*sin (wt) mv. Other in the circuit Assuming the values of the elements (2R1) = 1 ko, R2 = 0.5 MQ, and R3 = R4 = 10 ko, Calculate the voltage values at each node (7 nodes) shown in the figure. A1 RA R2 R3 2R| R3 A3 +. R2 On R4 A2 Un O
Parts D and E only please, thank you!
What can you say about AM DSB-FC, AM DSB-SC, and AM SSB? What do they have in common and their difference?
i need the answer quickly
Subject: Analog Electronic and Circuit Please Solve this question
Q6: When x, y and z are positive and less than 6, a certain magnetic field intensity may be expressed as H = 6x(1+y)'z ax + 3x²(1+z)³ ay - (x+1)yz² az. Find the total current that crosses the strip, x =3, 1 ≤ y ≤5, 3≤ z≤5, by using Stokes' theorem.
Where and How Simplex, Half Duplex and Full Duplex Modes are used in Real Life? Explain withExamples and Diagrams
(Boost de-dc converter with continuous inductor current. Evaluation of inductor and capacitor values) EX3: The boost converter shown bellow has the following specifications: Vin = de input voltage = 12 V, de output voltage = 30 V, output voltage peak-to-peak ripple = 1% Inductor current peak-to-peak ripple 10%, f;= switching frequency = 25 kHz and R = load resistance = 50 N Assuming that the converter is ideal, calculate: a) The duty cycle. b) The average input current. c) The minimum required inductance that ensures continuous inductor current. d) The required inductance so that peak-to-peak current ripple = 10%. e) The minimum and maximum values of the input current. f) The value of the output capacitor so that the output voltage ripple = 1%. g) Verify the theoretical results with the respective simulation ones. Boost inductor Output filter capacitor D VL 1R Vin S R Vo