C RI R2 The image above shows a spray nozzle. B and C are the only points connected to the both the outer and inner circle.A force of 2 Ibs is applied at A. Assume any values for the dimensions necessary to calculate deflection of the beams at B and C and produce a bending moment diagram. Note: ensure the value for the width at B is grater than the width at C.

Q: FIGURE 1. 40 kN 40 kN/m A B 20 kN/m E ए 2 m 1m 4 m 2 m R, R2 What is the maximum intensity of moment…

A: Draw SFD and BMD and answer the questions

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: -3 R3 - 10 10 Find the coordinates of the centroid 3.

A: To determine the coordinates of the centroid of the given object.   The geometry of the given object…

Q: Determine the y-coordinate of the centroid of the shaded area shown. 9" Parabolic. 4" Answer: y = i…

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: Find the range of: f(x)=Vx+4.

A:

Q: Now please solve 7-10

A: Some statements regarding highway and traffic engineering

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: DRAW HE FREE BODY DIAGRAM wooDa FLANK BOX 5K6.

A: To draw the free body diagram of the given box.   The purpose of a free body diagram is to represent…

Q: 1" 5" 2" 1-Determine the location of the centroid (x,y) of the centroid. 2- Determine the Ix0 and…

A:

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: Find the length of side TS.

A: Consider the figure,

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: Arc command and its abbreviation is A character is the only command can be used to draw an arc in…

A: It is required to state whether true or false statement.

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: Hidden line should be dimensioned. Select one: O True O False

A: Dimensioning to hidden lines should be avoided wherever possible. We should use auxiliary cross…

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: 80 mm -L- В D 60 mm

A:

Q: Let F₁ = [F1] N. i) Express F₁ as a Cartesian vector. F₁ X 3 5 4 30° 45° F₂= = 450 N - y

A: To represent F1 as a Cartesian vector. F1 = 647 N

Q: PROBLEM 2 The centroid of the T-section shown is 2.5 inches above the base. What should be the value…

A:

Q: answer this too please y bar put 3 demicals if possible

A: Centroid y = (A1y1-A2y2)/ (A1-A2)

Q: ex (x+1)² +c

A: Write all numerators above the common denominatorUse  to expand the expression.

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: The reduced form of 3y (0) – 21y (4) + 5y''– 10y"+42y'- 8y+ 5=0 js: A (3D5- 21D4+5D³ – 10D²+42D – 8)…

A:

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Identify the centroid of the 1/4 circle projected whose radius is r. Utilize integration. Yo -x Хо

A:

Q: 4.157 Find the forces in members CD, DH, and HI.

A: The given figure is shown below:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.