Please answer clearly Consider a three-stage amplifier of communication system that having itsfirst stage amplifier with power gain A1 = 1000, the second stage amplifiergain with power gain A2 = 100 and third stage amplifier with power gainAz = 10.(c)(i)Calculate each power gain of amplifier in dB.(ii)Determine the overall power gain in dB.(iii)Evaluate the output power in dBm if the input power is 5 µW.

(c) A 3-stage amplifier have, First stage gain (A1) = 1000 Second stage gain(A2) = 100 Third…

(c) Consider a three-stage amplifier of communication system that having its first stage amplifier with power gain A1 = 1000, the second stage amplifier gain with power gain 42 = 100 and third stage amplifier with power gain As = 10. (i) Calculate each power gain of amplifier in dB. (ii) Determine the overall power gain in dB. (iii) Evaluate the output power in dBm if the input power is 5 µW.

(c) Consider a three-stage amplifier of communication system that having its first stage amplifier with power gain A1 = 1000, the second stage amplifier gain with power gain 42 = 100 and third stage amplifier with power gain As = 10. (i) Calculate each power gain of amplifier in dB. (ii) Determine the overall power gain in dB. (iii) Evaluate the output power in dBm if the input power is 5 µW.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve question number 17, 18 and 19 for me. ***If you need the value of R or R' use R=5 ohm.*** Thank you.
Examiner: Ass. Prof. Dr. Adel M. Dakhil Time: 1.5 hr 2020-2021 Note: Answer al questions Question 1 A combinational switching network, has four inputs (a,b,c,d) and one output. The output is at logic (1) if two or more are at logic (0). Design the network circuit.
can ou please answer question d?
Question No. 9 Differentiate between Gray and BCD Codes.
The subject is Advanced Electronic Circuits Please send the answer by typing i don't want any handretten. Also, don't copy past from net as plagiarism will be counted.
Use the block diagram reduction please
3 For each of the following Boolean expression, do the followings: 3.1 H = AB + B a. Draw the electrical schematic diagram using IEC standardized referencing, symbol and terminal numbering. b. Describe the operation of the circuit 3.2 L = AB + AC + ABC a. Draw the electrical schematic diagram using IEC standardized referencing, symbol and terminal numbering. a. Describe the operation of the circuit 目

Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
i need the answer quickly
Identify the given statement. The FCC has designated a 20-MHz range of frequencies ranging from 88 MHz to 107 MHz to the commercial FM broadcast service. Select your answer. The statement is a case-to-case basis. The statement is false. The statement is true. The statement has no fixed information.
The subject is Communication Systems ( PULSE CODE MODULATION ) Please send the answer by typing i don't want any handwritten. Q4)Explain the process of sampling and quantisation & give example?